IMDTouchKnowledge BaseShop main store

Comparison

Choosing Free Modbus HMI Software for a Windows Panel PC

HMI and touchscreens Published 6 min read

Short answer

For a Windows panel PC that must show Modbus TCP data and alarms, Ignition Maker Edition and VTScada Lite are the only candidates with a free tier and a specific Modbus TCP claim on record. Maker Edition is documented free for non-commercial use only, so production machines bench-test VTScada Lite first or fall back to code-based AdvancedHMI.

On this page
  1. What each candidate actually claims
  2. Transport and function codes decide the shortlist
  3. The license line picks the winner
  4. The bench test that settles it
  5. The panel PC side
  6. The decision, case by case
  7. Questions asked

You asked for free software on a Windows industrial PC that takes Modbus points and turns them into screens and alarms. Two candidates carry a free tier and a specific Modbus TCP claim on record — Ignition Maker Edition and VTScada Lite — and the license terms decide between them. Maker Edition is documented by its vendor as free for non-commercial use only, so it belongs on benches and training rigs; a production machine goes to VTScada Lite first, with code-based AdvancedHMI as the fallback that never phones home. Node-RED, FUXA, IGSS and the rest stay candidates only until they pass the same bench test. If your station is a small terminal rather than a PC, start instead with lightweight HMI software selection for Modbus I/O control.

What each candidate actually claims #

Every name below arrives with a different weight of evidence, and the grade matters more than the name. Documented means the vendor states it in its own material. Reported means practitioners who used the tool say so. Named only means someone suggested it with no capability detail. A generic "Modbus" claim is not a Modbus TCP claim, and none of these reports is a compatibility test on your controller.

Candidate Modbus claim on record Evidence grade Cost and license on record Where it fits
Ignition Maker Edition Includes Modbus TCP Reported by users Free for non-commercial use, documented by the vendor Bench, training and hobby stations
VTScada Lite Free with Modbus TCP support Reported by users Reported free; tag and deployment limits not on record First candidate for a production station
AdvancedHMI Reads and writes PLC data over Modbus, from C# Reported by users Reported free, code you compile Stations where you own the code and want no license server
Node-RED Modbus connectivity through contributed nodes General capability, untested here Free and open source Supervisory dashboards on a trusted segment
FlowFuse Managed Node-RED deployment Named Commercial platform When Node-RED's instance and security gaps need managing
FUXA None on record Named only Not on record Only after passing the bench matrix
IGSS None on record Named only Not on record Only after passing the bench matrix
WinTr None on record Vendor listing Listed as free SCADA for Windows with scripting in C#, VB.NET, JavaScript and Python Screen-heavy projects needing custom scripts

Transport and function codes decide the shortlist #

Modbus is a family, not one protocol. Over Ethernet it is Modbus TCP; over RS-485 it is Modbus RTU, and a driver that speaks one does not automatically speak the other. Only Maker Edition and VTScada Lite carry a specific TCP claim on record; AdvancedHMI's claim is "Modbus" with the transport unstated, so open its driver list before you write logic, not after.

Function codes set the read and write limits you design against. The Modbus Application Protocol specification caps a single read at 125 registers or 2000 coils, and writes split by type: FC05 for one coil, FC06 for one register, FC16 for a block of registers, FC22 to mask bits inside a single register. One failure pattern is worth knowing before the bench: if writes reach coils but a bit inside a holding register never changes, the driver is probably issuing an FC22 mask write the server does not implement. Move that tag to its own coil, or write the whole register.

The license line picks the winner #

Maker Edition's own page documents it as free for non-commercial use. That clause is the whole test: a machine whose product is sold is commercial, period. On top of that, the vendor's forum carries an open request to make the Maker license permanent instead of leased — users describe revalidating it periodically rather than holding a file — so plan for the panel PC to reach the activation server now and then. Decision: bench, training and hobby stations yes; production no.

VTScada Lite is the first candidate for a commercial station, because a named vendor publishes it and users report both the free tier and the Modbus TCP support. The Lite tier's tag limit and deployment rights are not on record here, so get those numbers in writing before you build hundreds of tags around them.

AdvancedHMI trades money for ownership: it is reported free, it compiles into your executable, and no license server sits between your operator and the screen. The price is that alarms, trends and screen revisions become your codebase to maintain. Node-RED is free and open source too, with the weaknesses practitioners name — multiple instances and security — which is exactly the gap the managed commercial platform FlowFuse was built to close. For the wider question of what money buys at all, read paid versus free SCADA software differences.

The bench test that settles it #

  1. Fix the sheet before the software: transport, unit or slave address, and for every tag its address, data type and read-or-write direction.
  2. Install the candidate on the actual panel PC — not your laptop — and connect to the actual controller with ten tags spanning every data type you use.
  3. Prove writes with the machine in a safe state, and verify each value lands where you think it does.
  4. Pull the Ethernet cable and prove the alarm path: the failure must show on screen within the time you set, and restoring the link must restore data without a restart. Follow the same discipline as proving a PC-based HMI before replacing panel terminals; for the alarm screen itself, creating a SCADA PLC communication alarm for link loss covers the wiring of that one display.
  5. Power-cycle the PC and confirm the project auto-starts and reconnects; on Maker Edition, note what the leased license does across that restart.

None of these packages is a safety controller: emergency stops and interlocks stay hardwired or in the safety PLC, never routed through the HMI screen.

Worked example: poll load #

Take a station needing 96 holding registers (FC03), 24 input registers (FC04) and 40 coils (FC01) once per second, plus 6 operator setpoint writes (FC06) on demand. The specification's service limits are 125 registers and 2000 coils per read request, so each read group fits in one request: 96 ≤ 125, 24 ≤ 125 and 40 ≤ 2000. Steady state is 3 read requests per second.

At an example 100 ms round trip per request — a lazy LAN figure, not a measurement — the driver occupies 3 × 100 ms = 300 ms of every 1000 ms cycle, a 30% duty on one TCP connection. Six writes landing in the same second add 6 × 100 ms = 600 ms, for 900 ms of that second and 100 ms spare: stagger multi-setpoint operations or accept an occasional slow cycle. The tag counts and the 100 ms figure are example inputs; the 125 and 2000 limits are the protocol's.

The panel PC side #

When the PC itself is part of the change, industrial panel PCs put the Windows runtime and the touchscreen in one unit at the machine, and a washdown area or an existing cut-out changes which unit that is. Size the host like any HMI server: RAM, SSD and Windows sizing for an HMI panel PC is the checklist.

The decision, case by case #

  • Bench rig, trainer, home or hobby machine: Ignition Maker Edition — the fullest free package, non-commercial license, leased activation accepted.
  • Commercial production station: VTScada Lite first, tag limit confirmed in writing; AdvancedHMI when you would rather own the code than count anything.
  • Supervisory dashboard on a trusted segment: Node-RED, hardened, or FlowFuse when instance management must be someone else's problem.
  • FUXA, IGSS, WinTr or any other name: a candidate only after it passes the same bench matrix on your controller.

Questions asked

Is Ignition Maker Edition free for a machine on our production line?

No. The vendor documents Maker Edition as free for non-commercial use only, and a line that ships product is commercial. Keep it on the bench, on training rigs and on hobby machines. Reports on the vendor's own forum also describe the license as leased rather than permanent, so the PC revalidates it periodically instead of holding a permanent file.

How many tags can VTScada Lite run?

No tag count is on record in the material behind this comparison. The free license and the Modbus TCP support are practitioner reports rather than a vendor specification we can cite. Get the current Lite tag limit and deployment rights in writing before you design screens around them, then run the bench poll with your real tag count to confirm the number holds.

Which option needs no license server or activation at all?

The code-based options. AdvancedHMI compiles into your own executable and Node-RED runs as an open-source runtime; neither checks a license server at startup. The trade is ownership: alarm logic, screen versions and driver updates become code you maintain. Confirm the transport your AdvancedHMI driver build supports before you commit the project to it.

Can Node-RED be the plant alarm display?

Not as the only alarm path on today's evidence. Node-RED is free and open source, but practitioners flag multi-instance handling and security as its weak points, which is the reason the managed platform FlowFuse exists. Use it for a supervisory dashboard on a trusted network segment, and keep machine-critical alarms where a lost link cannot hide them.

What if writes reach coils but a bit inside a register never changes?

That pattern is a function-code symptom. Coil writes travel as FC05 and whole-register writes as FC06, but a single bit inside a holding register is often sent as a mask write, FC22, which not every Modbus TCP server implements. Move the tag to its own coil or register, or configure the driver to write the full register instead.

Keep reading

  • Selection guide

    Do You Need SCADA Software for a Modbus HMI Project

    No. Modbus only proves a possible data link, so pick the runtime target first: a touch panel programmed by its own editor for machine-side parameter control, or a licensed PC SCADA runtime when the screens must run on a computer. The documented demonstration mode of a Vijeo Citect-class runtime stops after about 15 minutes with live devices, which settles a bench test but not continuous operation.

    HMI and touchscreens

  • Selection guide

    Choosing a PC-based HMI runtime for a Modbus TCP PLC

    No — C-more projects deploy to C-more panel hardware, so a PC-only interface needs a PC runtime instead. Run AdvancedHMI, a PyQt5 front end with pymodbus, or an Excel VBA socket client as the Modbus TCP client, with the PLC acting as the server on TCP port 502.

    HMI and touchscreens

  • How-to

    Running a PLC-hosted visualization on a remote HMI panel PC

    The PLC-hosted visualization reaches a panel PC through a panel-side PLC HMI client deployment: install the client for the panel platform, confirm the license, run the remote-client deployment that selects the hosting PLC, verify the network path, and start the client from a CE shell command. Downloading TargetVisualization to the PLC only feeds a monitor connected to the controller; it installs nothing on the panel.

    HMI and touchscreens