IMDTouchKnowledge BaseShop main store

Troubleshooting

Fixing a Vijeo Designer USB transfer filesystem path error

HMI and touchscreens Published 6 min read

Short answer

The [HMIS] filesystem path error means the software resolved the wrong transfer destination, and the connection-abort line is only its consequence. Because the failure sits on one workstation, compare that PC's target selection, transfer method and installed version against a working one before touching the Runtime installer, and keep the two-to-three-times-slower USB-key route as a fallback.

On this page
  1. What does the [HMIS] filesystem path error mean?
  2. Is the cable or the panel hardware at fault when only one PC fails?
  3. What do I compare between the failing PC and a working one?
  4. Should I touch the Runtime installer to fix this?
  5. If I update my copy, does the whole team have to update too?
  6. How much is the USB-key workaround really costing?
  7. How do I restore the direct transfer without losing the cause?
  8. How do I confirm the fix held?
  9. Questions asked

Treat the filesystem-path message as the real fault and the connection abort as its consequence. Your copy of the SoMachine-bundled Vijeo Designer is rejecting the transfer destination it resolved for the target before any project data moves, and because your PC is the only one failing against an HMIS85 with its HMIS5T module that your colleagues' stations still serve without the error, the difference lives on your workstation: the selected target, the transfer configuration, or the installed version. Fix it in that order — record the exact version, compare it with a working station, and match that station's transfer selections — and leave the Runtime installer on the panel out of the first attempt. Keep the USB-key route, reported at two to three times the direct-transfer time, as the fallback rather than the fix.

What does the [HMIS] filesystem path error mean? #

It means the transfer destination that Vijeo Designer resolved for the target is not a usable filesystem path: the software rejects the destination during transfer setup, then terminates and reports the connection error, so the path line is the cause and the abort line is the consequence. The path is evaluated before the link carries anything. A genuine connection fault aborts on its own, without a complaint about a path, so read the two lines in that order and work the first one. A transfer that dies on connection while the target still answers ping is a different mechanism altogether — see Why an HMI Transfer Fails in Initial Start Mode Despite Ping for that case.

Is the cable or the panel hardware at fault when only one PC fails? #

No. When the same panel and module accept transfers from other workstations on the same shared project, the cable, the module and the panel are proven good, and the fault sits in your workstation's selection, configuration or installation. Swapping hardware would replace known-good parts while the actual variable — your PC — stays unexamined. The fact that this hardware worked for you before tells you the combination is capable, not what changed; the comparison in the next section answers that.

What do I compare between the failing PC and a working one? #

Five things, in this order: the complete error text, the installed version, the selected target, the transfer method, and a swap test that separates the PC from the project. Do the comparison before changing anything, so a success later has a traceable cause.

  • Capture the exact failure. Reproduce once and record the complete message pair, including the [HMIS] path text and the abort line, and confirm the attempt was a direct transfer rather than a key transfer.
  • Read both version numbers. The failing installation in the reported case displays V6.2.3.217 SP3.1 217-219; write down the number the working PC displays instead of assuming it is newer.
  • Open the same project on both PCs. Confirm the same target is selected, the expansion module appears as expected, and the destination the transfer setup offers is the panel itself.
  • Compare the transfer method. Direct connection and removable-media transfer are different routes in the transfer setup; note which one each PC uses.
  • Run one swap test. Push your project from the working PC, then push a known-good project from yours, and record where the error follows.
Swap-test result Fault location Action
Error follows your PC with either project Workstation configuration or installation Correct the transfer setup, then align the version
Error follows one project from either PC That project's target or transfer settings Correct the destination inside the project
No error after matching the selections A stale or wrong selection on your PC Keep the matched configuration and verify it persists

Should I touch the Runtime installer to fix this? #

Not as the opening move. A path error raised by the workstation at transfer setup does not implicate the runtime installed on the panel, and reinstalling it changes the target before you have a cause. The runtime is a target-side component; this failure is raised host-side, against a panel that other stations still transfer to successfully. Runtime installer work also fails in its own ways — when the installer cannot find its target, that is the separate problem covered in Fixing a Vijeo Designer Runtime Installer Target-Not-Found Error. If the comparison ends at a version or installation difference, take the supported update or repair path from there, not improvised changes to runtime components.

If I update my copy, does the whole team have to update too? #

Update only to the exact version the working stations already run, and then nobody else changes anything; going beyond the team's level is what creates the forced-update question, so do not go beyond it. Your own hypothesis — that your colleagues updated and you did not — is confirmed or killed the moment you read their version numbers; if they differ, bring your PC to their exact level and the question closes. When you do update, follow the documented sequence and install the HMI base software before the service pack, because the service pack expects the base software underneath it.

How much is the USB-key workaround really costing? #

Two to three times the direct-transfer time per download, the ratio reported from this development bench, and that multiplier is what decides how long you tolerate the fallback. Work it out with round numbers as an illustration: a direct download that takes 6 minutes costs 12 to 18 minutes by key (6 × 2 = 12, 6 × 3 = 18), because you write the key, carry it to the panel and import it there. Ten downloads across a commissioning day is 120 to 180 minutes of transfer time (12 × 10 = 120, 18 × 10 = 180) — two to three hours spent not testing. The workstation comparison above takes minutes, so that trade decides how long the fallback survives. Note also that a successful key transfer certifies nothing about the direct link: it is a different path through different software stages and can work while the direct route is broken.

How do I restore the direct transfer without losing the cause? #

Change one variable at a time from a saved baseline: back up the project, match the known-good selections, correct the destination, retry, and record what actually restored the transfer.

  1. Back up the project and write down your workstation's current version and transfer settings as the rollback point.
  2. Select the same project, target and transfer method the working PC uses, and confirm the destination shown in the transfer setup is the panel, not a removable-media path.
  3. Correct that destination if it is wrong — this is the single most likely fix for a filesystem-path complaint — and re-check it in the setup before starting.
  4. Put the machine in a safe state first: the panel's runtime restarts during a transfer, so the operator interface disappears partway through and the machine must not depend on it then.
  5. Retry the direct transfer over the same physical link that works from the other PC, changing nothing else.
  6. If the error returns, only now compare the recorded versions and take the supported update or repair path.

How do I confirm the fix held? #

A completed file copy is not the test: confirm the application runs on the panel from the direct transfer, then close and reopen the project on your PC and transfer once more to prove the corrected selection persisted. The first success shows the route works; the second shows the configuration survived a reload. Then make the direct route your default again for the next development iteration and keep the key for occasions when the direct link is genuinely unavailable — which, on the evidence here, it is not.

Questions asked

Does the [HMIS] path error mean my USB key is formatted wrong?

No. The error appears on the direct-transfer route before the key is involved, so the key is not the cause. The format only matters on the fallback route: use a small stick formatted FAT32 and keep destination folder names short, without spaces or special characters, which is the combination this software handles most predictably.

What happens to shared projects if I update past my coworkers' version?

Treat a project saved by the newer build as openable only by that build until you have proven otherwise. Before handing the file back, update, open a copy of the project, save it, and have a coworker on the older build try to open that copy. If it fails, the whole team moves up together; if it opens, you have your answer with nothing shared at risk.

Does it matter that my Vijeo Designer came bundled with SoMachine?

It changes where the update comes from, not how you diagnose. Read the version number each PC displays, align the failing station to the level the working ones run, and take the update path that matches your bundled installation rather than a standalone download. The comparison method in this article is the same either way.

Why is the option to transfer the license to removable media greyed out?

The documented cause is that the tool cannot determine the computer ID, so the option is withdrawn until that condition is resolved. Fix it through the vendor's licensing documentation rather than a workaround. It is unrelated to the transfer path error in this article, which needs no license option at all.

Keep reading

  • Troubleshooting

    Why an HMI Transfer Fails in Initial Start Mode Despite Ping

    Ping success proves only that the panel's IP stack answers. On a new Magelis XBTG in Initial Start Mode, run three checks in order: build in the engineering version that still supports the target (Vijeo Designer 6.2 for XBTG), clear the license so the download command activates, then load runtime and application over one transport at a time.

    HMI and touchscreens

  • Troubleshooting

    Fixing a hardware controls error on an HMI Ethernet link

    The message means the HMI editor cannot fit the project's controller driver or Ethernet feature onto the panel model you selected, so validation stops before any data is sent. Correct the panel target and driver in the project first; IP addresses and cabling come after the project compiles. The working RS-485 link only proves the serial path.

    HMI and touchscreens

  • Troubleshooting

    How to get Vijeo Designer Basic 1.1 from the official source

    The shared address is cut off where the file name should continue, so it cannot fetch anything. Recover the package from Schneider Electric's download area by searching "Vijeo Designer Basic" and opening the V1.1 entry, an EXE of about 370.8 MB documented in SEVD-2020-133-02, then confirm the exact HMIGXU target and PLC driver before installing.

    HMI and touchscreens