IMDTouchKnowledge BaseShop main store

Troubleshooting

Touch calibration fails or drifts: separate the real causes

HMI and touchscreens Published 7 min read

Short answer

If calibration fails repeatedly, the fault is usually the calibration tool, its driver or session state, not the touch sensor: a pass that stops with an error before the target pattern runs never changes stored coordinates. Calibration persists until firmware changes, so test several touch targets first — one dead button is an application-event fault, and only a whole-screen offset that keeps returning is true drift.

On this page
  1. What a calibration failure can and cannot tell you
  2. First checks before you recalibrate again
  3. Separate the three real causes
  4. Working the uLCD-43PT case in Workshop 4: from error to decision
  5. When true drift is the cause
  6. Prove the fix before you close the ticket
  7. Questions asked

When a touch panel asks for calibration again and again, suspect the calibration tool before the sensor. A pass that stops with an error message before the target pattern ever appears has not touched the stored coordinates, so the fault sits in the tool, its driver or the session it runs in — and calibration itself persists until firmware changes. Before recalibrating, test several touch targets across the screen: one dead button is an application-event fault that calibration cannot repair, and only a whole-screen offset that keeps coming back is true drift. This article gives the stage-by-stage reading of a calibration failure, a first-checks list, a decision table for the three real causes, and one worked example from a uLCD-43PT whose Workshop 4 calibration utility failed with "Unexpected response to L" on every attempt.

What a calibration failure can and cannot tell you #

Calibration is one stored mapping between the sensor's raw touch positions and the display's pixel grid. The panel applies it to every touch on the whole screen, and it holds until something rewrites it: a firmware flash, an explicit reset or a completed calibration pass. Sort the utility's behavior into three stages:

  • The startup exchange fails before any target appears. The tool and the panel cannot agree on the handoff, so the calibration utility never runs and no coordinate is written.
  • The transfer fails. The tool begins moving the calibration utility onto the panel and stops on a size or timeout error. Still no target pattern, still no coordinate change.
  • The pass completes. Only after the panel has accepted the target sequence does the stored mapping change, and only then can its accuracy be judged.

Read each message for its stage, not for a hidden sensor diagnosis. A stage-one or stage-two failure is a tool fault by construction: a calibration that never ran cannot have spoiled the coordinates it never wrote. Treat reported reply values, such as the value 21 in this case's startup error, as the tool's record of the exchange — not as a fault code to decode before the stage is known.

First checks before you recalibrate again #

Run these before the next attempt; each removes a cause that masquerades as drift:

  • Confirm the application is running. A failed download can leave the display blank, and a blank screen proves nothing about touch response.
  • Check what changed since the last good calibration. If the firmware was flashed since, the old calibration is legitimately gone and one pass is due; if nothing was flashed, a fresh demand for calibration points elsewhere.
  • Update or reinstall the touch driver first, obtained through the manufacturer or an authorized distributor. On a Windows panel PC, start from "Calibrate the screen for pen or touch input" in Windows search, run the calibration the model's documentation names with the input type it names, and where account rights block the utility, follow running touch calibration without administrator rights on a panel PC.
  • Check the display configuration. Multiple monitors or changed display settings can leave the new mapping applied to the wrong surface.
  • Keep hands off during the target sequence. A touch while the targets are presented can store a false calibration, and it persists exactly like a real one.
  • Expect a restart on some systems: several utilities apply the new mapping only after a reboot, and a pass that reported an error should be repeated, not saved.

Separate the three real causes #

A coordinate fault moves every target. That is the whole test: touch several targets spread across the screen and compare what happens at each.

Symptom at the screen Cause What fixes it
Every target lands on its neighbor by the same offset; calibration corrects it and it stays corrected One-time coordinate fault, typically after a firmware flash or first bring-up One calibration pass, then stop
The offset keeps returning, and the interval between recalibrations shrinks Aging resistive touch surface Plan replacement of the touch surface or panel
One object dead while its neighbors respond The object's event handling or its downstream command path Fix the object: check its state, overlapping graphics, the event handler and where its command goes
The calibration utility errors before any target appears Tool, driver or session fault Fix the tool: driver update, fresh session, corrected release

Misses that bunch up near the edges of a capacitive screen are a fourth thing entirely, and not calibration — why capacitive touch buttons miss presses near screen edges covers that behavior. For the single dead object, keep one distinction: a touch event that never fires is not the same fault as a command that fires and goes to the wrong destination. Calibration sits upstream of both and repairs neither.

Working the uLCD-43PT case in Workshop 4: from error to decision #

One reported failure shows the whole chain: repeated calibration attempts that never reached the targets, and a button fault that calibration never had a chance to touch.

Inputs #

Each input comes from the reported case:

  • Display module: uLCD-43PT. Engineering tool: Workshop 4.
  • Error at the startup exchange: "Unexpected response to L, Response Len = 1 Response = 21." — a reply of length 1 carrying the value 21.
  • Retry from a blank visi project: "Response len = 0 Response =" followed by "Timeout downloading" — a zero-length reply, then no reply before the tool's timeout.
  • Error when the transfer did start: "Unexpected file size".
  • Persistence rule for this module: calibration sticks until the PmmC changes.
  • Release carrying the fix: Workshop 4.0.2.13.
  • Time spent on repeated calibration attempts: over half an hour. Time the deciding target test needs: about a minute.

The rule in words #

Every error above stops the tool before the calibration target pattern appears. A pass that never shows its targets never writes a coordinate. So the number of coordinate changes those attempts made equals completed passes multiplied by the one coordinate write each completed pass performs.

The arithmetic #

Completed passes: 0 — each attempt stopped at the startup exchange or the download stage. 0 × 1 = 0 coordinate changes: after over 30 minutes of attempts, the stored calibration was exactly what it had been before the first attempt. The cost comparison ran the same wrong way: over 30 minutes spent on a cause already excluded, against about 1 minute for the target test that decides it — a ratio worse than 30 to 1.

Result and decision #

Result: the touch layer was never proven faulty; the tool session was, and the button that would not react remained an application-event fault.

Decision: install the Workshop release that carries the fix — 4.0.2.13 — or a later release whose compatibility notes cover this display and project, sourced through the manufacturer or an authorized distributor, before the next calibration attempt. Until the update lands: open a fresh session, load only a program configured for the display, run Tools → Touch Calibration, and after a clean pass force a fresh compile with Ctrl+F9 before downloading the application; if the calibration program leaves the session stale, restart Workshop or switch to another tab and back. Adopt the threshold the case proves: run the target test before any recalibration, because the test costs about a minute and the excluded cause costs half an hour.

When true drift is the cause #

True drift has a signature. The offset appears gradually, affects the whole screen with the edges worst on a resistive film, and each calibration holds for a while before the error creeps back. On a resistive panel that is the wearing surface doing what wearing surfaces do: the film's coating degrades with use, and the raw coordinates wander with it.

Rate tells you what you are looking at. An offset that builds over months and resets with one calibration is wear; plan for it. An offset that appears over hours, or that tracks machine temperature, points at the electronics — a loose ribbon connector or a drifting component — not at wear. Calibrate once and time the result: if the next recalibration is months away, stop calibrating; if the interval shrinks run over run, the surface is dying.

When the wear is real, the endgame is hardware: replacing the display and its touch surface while the computer or controller stays is exactly the job for industrial touchscreen monitors.

Prove the fix before you close the ticket #

  • Run the calibration utility through its complete target sequence with no error text; save a clean pass, and repeat rather than save any pass that reported an error.
  • Reload the application and confirm its normal screen appears — not the blank screen a failed download leaves behind.
  • Touch targets near all four corners and the center; the object selected must be the object touched.
  • Operate the button that started the investigation; watch its local response and the action it triggers downstream.
  • Power-cycle through the machine's approved procedure and repeat the corner checks without flashing anything; a good calibration survives the restart.
  • Before returning the machine to production, prove each touch lands on the control intended — a mis-mapped touch on a running machine can command the wrong output.

Questions asked

Does touch calibration survive a power cycle?

On the uLCD-43PT it does: calibration sticks until the PmmC changes, so power cycles and application downloads leave it alone. On a Windows panel PC, the saved mapping stays until the touch driver is reinstalled or the display configuration changes. If the panel demands calibration after every power-up, the storage is not your real problem — chase the tool session, the driver or the touch hardware instead.

Why does calibration fail with my project loaded but work in a fresh session?

In the reported case the identical errors appeared even from a blank visi project, so the project was not the trigger. A session already running an application holds the communication path the calibration utility needs. Calibrate from a fresh session with only a program configured for the display loaded, then force a fresh compile with Ctrl+F9 before downloading your application — or move to the release that fixes that session handling.

Do capacitive screens need the same calibration as resistive ones?

Far less often. Projected capacitive sensors are aligned to the display where they are built, so a capacitive panel that suddenly seems drifted usually had a driver update, a display change or altered video settings behind it rather than a wearing surface. Resistive films measure position through physical contact, so they genuinely need target-pattern calibration, and their slow drift over months of use is wear you can plan a replacement around.

What should the maintenance record hold after a calibration fault?

Record the tool name and exact release number, the display model, the full error text, the stage where the run stopped — startup exchange, download or after the targets — whether firmware was flashed since the last good calibration, and how long the previous calibration held. Those details separate a tool regression from a communication fault or an application-event problem the next time the symptom appears.

Keep reading

  • Troubleshooting

    When Only One Touchscreen Icon Responds to Press

    If only one of several icons answers a press, the others are most likely status indicators: they display state but never accept input. Read each object's role in the configuration tool before touching hardware — a healthy screen shows exactly as many responsive icons as it has assigned press actions, and a silent indicator is correct behavior, not a dead touch area.

    HMI and touchscreens

  • Troubleshooting

    Why Capacitive Touch Buttons Miss Presses Near Screen Edges

    Most first-press misses on a capacitive HMI happen because the controller's estimated finger center lands a few millimeters outside the software button's hit-test bounds, especially near screen edges. Log the reported coordinates during a held press: if they fall outside the button, enlarge the pressable region by the logged offset. Only when the touch count stays zero during contact should you chase grounding, polling or hardware.

    HMI and touchscreens

  • Comparison

    Capacitive vs resistive touchscreen with oily gloves and pens

    For an oily-glove line, choose a touchscreen by testing the exact panel, glove and pen together. Standard resistive panels accept pressure from a gloved hand or a suitable passive stylus; projected-capacitive glove and pen support depends on the controller and its configuration. A single-touch replacement cannot provide a two-finger pinch, but it may still support dragging and one-finger swipes through the application.

    HMI and touchscreens

How to Rotate a 3D Object on a Touch Panel With Drag Input