IMDTouchKnowledge BaseShop main store

How-to

Connecting a Fuji HMI to a ControlLogix PLC

HMI and touchscreens Published 5 min read

Short answer

Yes, the pairing works. You need Rockwell's Logix package matched to the controller firmware on the PLC side and Fuji V-SFT for the panel; FactoryTalk View programs only Rockwell panels, and RSLinx is not part of the Fuji data path. The gate is the driver list for your exact panel model — V8, V9 and TechnoShot have the Allen-Bradley connection documented.

On this page
  1. The two packages that do the whole job
  2. Match the Logix license to the controller firmware
  3. Confirm the panel's Allen-Bradley driver
  4. Configure the panel project in V-SFT
  5. Network settings and the proof test
  6. The decision, case by case
  7. Questions asked

Yes, a Fuji MONITOUCH talks to a ControlLogix or CompactLogix controller, and the job needs exactly two engineering tools: the Rockwell Logix package matched to your controller's firmware, and Fuji's V-SFT for the panel. FactoryTalk View is not one of them — it builds screens for Rockwell's own panels and has no path into a Fuji project — and RSLinx is not part of the panel's data path either. The single gate is the driver list for your exact panel model, and for the V8, V9 and TechnoShot series the Allen-Bradley connection is documented by Fuji. This page walks the whole path: license match, driver check, project build, and the test that proves the data.

The two packages that do the whole job #

Job Package What it settles
Controller program RSLogix 5000 or Studio 5000 Logix Designer Which line you buy is fixed by the controller's firmware revision, matched in the next section
Panel screens and PLC connection V-SFT Builds the MONITOUCH project, selects the Allen-Bradley driver, downloads to the panel
Rockwell operator panels FactoryTalk View Not part of this job; it does not program a Fuji panel

That vendor-tool-to-own-hardware pairing holds across the industry, and the per-manufacturer detail is in which HMI software works with which HMI panel hardware. RSLinx stays on the Rockwell engineering side, providing driver and browsing support to Rockwell's own tools; it never sits between the panel and the controller.

Match the Logix license to the controller firmware #

Read two things off the controller before any purchase: the full catalog number and the firmware revision. Rockwell's published compatibility list splits the line at v21: RSLogix 5000 v13 through v20.04 covers the earlier revisions, and Studio 5000 Logix Designer v21 and higher covers firmware v21 and up. A GuardLogix on the machine changes nothing here, because GuardLogix controllers support the standard ControlLogix functions and present the same data path to a panel.

Illustrative worked example, arithmetic shown. The controller properties report firmware revision 21.3. Compare: 21.3 > 20.04, so the RSLogix 5000 line ends below this controller and the license is Studio 5000 Logix Designer v21 or higher. Had the revision read 20.0, then 20.0 ≤ 20.04 and RSLogix 5000 v20.04 is the correct buy. Read the revision before buying the license, never after.

Why the Logix side accepts only Rockwell's own tool is a story of its own, told in why only Studio 5000 programs a ControlLogix 5571.

Confirm the panel's Allen-Bradley driver #

Ethernet capability proves only that the panel has a port. What proves the conversation is the driver table for the exact model. Fuji documents connecting a MONITOUCH V9 to an Allen-Bradley PLC and states that the same instructions apply to the TechnoShot and V8 series, so for those panels the compatibility question is answered in print. The wider MONITOUCH range — V10, V9, X1, WMI and TECHNOSHOT SMART — is listed with around 400 serial and Ethernet PLC drivers, but a range-wide count is not a model-by-model guarantee: a panel outside the V8, V9 and TechnoShot set is decided by the driver table in its own manual, and no Ethernet port substitutes for a missing driver. The X1, V10 and V9 series are programmed in V-SFT version 6.

Configure the panel project in V-SFT #

  1. Create a new V-SFT project for the exact panel model; the PLC connection settings live in the project's device setup.
  2. Select the Allen-Bradley driver for the Logix controller family, with Ethernet as the connection method.
  3. Enter the controller's IP address and the station or node fields exactly as the Fuji manual documents them for that driver.
  4. Build one test screen: a numeric display pointed at a controller value, in the address or tag format the driver documents for Logix controllers.
  5. Transfer the project from V-SFT to the panel.

Network settings and the proof test #

Over Ethernet the panel and the controller hold a CIP conversation, and the Logix-side mechanics are laid out in connecting a CompactLogix PLC to an HMI over EtherNet/IP.

  1. Put both devices on one subnet. Illustrative values: controller 192.168.1.10, panel 192.168.1.20, mask 255.255.255.0 — both addresses fall in 192.168.1.0/24, so one switch connects them and no router is involved.
  2. Ping the controller from a laptop on that subnet; success proves reachability and nothing more.
  3. Open the test screen and watch a value that changes in the controller, such as a free-running timer's accumulated value. When the panel tracks it, the driver path is proven end to end.
  4. Run one write against a non-hazardous test tag and confirm the controller receives the intended value. Never run the write test against an output that can move the machine.
  5. Rehearse the screens before the line is involved, the way covered in testing HMI simulation against a live PLC.

The decision, case by case #

  • Panel is a MONITOUCH V8, V9 or TechnoShot, controller is a ControlLogix, CompactLogix or GuardLogix: proceed. Buy the Logix package the firmware revision dictates, use V-SFT for the panel, and leave FactoryTalk View out of the purchase.
  • Firmware at or below 20.04 puts you in the RSLogix 5000 line; firmware 21 or above puts you in Studio 5000 Logix Designer.
  • Panel outside the V8, V9 and TechnoShot set: stop at that model's driver table before buying anything, because the port does not substitute for the driver.
  • Ping succeeds but reads fail: the fault is driver selection or address format, not the cable.

Questions asked

Do I need RSLinx for the MONITOUCH to read the PLC?

No. RSLinx serves Rockwell's own engineering and browsing workflows on the PC side. The panel reaches the controller through the Allen-Bradley driver configured inside the Fuji project, over the Ethernet network, with no Rockwell utility in the path. Keep RSLinx installed only if you also use it alongside the Logix tools themselves.

Does a ping or a link light prove the HMI will read PLC data?

No. A ping proves IP reachability and a link light proves the physical port; neither touches the application conversation. Only a value on the panel that tracks a changing controller tag proves the driver path end to end. If the ping succeeds while reads fail, work on driver selection and address format, not cabling.

Will a Logix 5000 Professional license program any Logix controller?

The edition is not the gate; the version is. Firmware at or below v20.04 opens in RSLogix 5000 v13 through v20.04, and firmware v21 and above needs Studio 5000 Logix Designer v21 or higher. A Professional license at the wrong version still fails, so read the controller's revision before purchasing.

Which MONITOUCH models have the Allen-Bradley link documented?

Fuji documents the connection for the V9 series and states the same instructions apply to the TechnoShot and V8 series. The wider line — S6, V7, V8, V9, V10, X1 and the TechnoShot ranges — ships with a large PLC driver library, but each model's own manual is the authority. For S6, V7, X1, WMI or TECHNOSHOT SMART, check that model's driver table before assuming support.

Keep reading

  • How-to

    Connecting Operator Terminal Expert to a Third-Party PLC

    Operator Terminal Expert connects to a third-party PLC through a protocol both ends document — typically Modbus TCP or RTU, or OPC UA with the HMI as client and the PLC as server. Select the driver for your exact terminal target, match the driver's address notation to the PLC's register references, and prove one read and one controlled write on the deployed terminal before mapping the rest.

    HMI and touchscreens

  • How-to

    Connecting One NS-Series HMI to a Redundant CS1D and a CP1H

    Yes. One NS-series panel hosts both controllers: a duplex CS1D pair whose Ethernet units keep a single system IP address through CPU changeover, so the panel never selects a CPU, plus a CP1H reached through its CIF41 as a second host. Both links run FINS over Ethernet simultaneously.

    HMI and touchscreens

  • How-to

    Connecting a Weintek MT8050iE to an S7-200 over PPI

    Yes. The MT8050iE talks to an S7-200 CPU 224XP over PPI with the Siemens S7/200 PPI driver in EasyBuilder Pro, assigned to a COM port documented for RS-485 with serial settings matched to the PLC. Project download runs over a USB A-to-mini-B cable or Ethernet and is independent of the PLC driver; confirm the real-time clock in the model datasheet.

    HMI and touchscreens