IMDTouchKnowledge BaseShop main store

Troubleshooting

Fixing HMIRTM.EXE Runtime Crashes on a Comfort Panel

HMI and touchscreens Published 7 min read

Short answer

The HMIRTM.EXE serious error is the HMI runtime crashing on the panel itself, most often because internal storage filled with accumulated logs. Back up to a USB stick from the panel operating system, delete the logs, and stop the runtime before changing the IP address; the failed ping is a network fault that sits below the project layer.

On this page
  1. What the HMIRTM.EXE shutdown actually is
  2. Two faults are stacked
  3. Back up over USB before deleting anything
  4. Free the storage that killed the runtime
  5. Stop the runtime before changing the IP address
  6. Prove the Ethernet path with numbers
  7. The MAC address route and the version ceiling
  8. The sequence that closes it out
  9. When to stop repairing
  10. Questions asked

An HMIRTM.EXE serious error is the HMI runtime process dying on the panel itself, and in most reported cases the panel survives it: internal storage has filled with accumulated alarm and data logs, or the runtime data has corrupted. Work the fault in that order — USB backup from the panel operating system, storage cleanup, then the network. The message Permission Denied. IP setting cannot be change during operation is a separate, smaller fault: the runtime was still running when the address was edited, so stop it first. A ping with no reply sits below both, because no tag, project or controller setting explains a dead IP path.

What the HMIRTM.EXE shutdown actually is #

HmiRTm.exe is the WinCC runtime process running under Windows Embedded Compact on the panel. When it reports that it encountered a serious error and must shut down, visualization stops and the panel usually returns to an error or startup screen, sometimes in a loop. The fault is local to the panel: a bad tag or an offline controller degrades what the display shows, it does not kill the runtime executable.

Reported causes cluster in three places, in the order worth testing:

  • Internal storage filled by alarm and data logs that were never bounded.
  • Corrupted runtime data in the project's storage folders.
  • An error in the project itself, which support names once the first two are clean.

Storage is the only cause you can measure and repair without touching the project, so it goes first.

Two faults are stacked #

The screen is showing more than one problem, and they do not share a cause. Test them separately.

What you see Layer that owns it First move
HMIRTM.EXE encountered a serious error and must shut down Runtime and local storage Back up, then free storage
Permission Denied. IP setting cannot be change during operation Runtime still in operation Stop the runtime, then edit the address
Ping gets no reply Cable, adapter, addressing Link and subnet checks before any project work
Service tool cannot connect to the target device Interface selection and transfer settings Plain Ethernet method, panel in transfer mode

A controller binding cannot explain a failed ping, and a network fault cannot kill a runtime executable. Do not start at the project while the panel is unreachable.

Back up over USB before deleting anything #

The panel operating system carries a built-in backup function that writes a restore archive to a USB stick. It needs no runtime and no network, which is exactly why it is the first step here: the runtime is faulted and the network path is unproven. Run it, then open the archive on a PC and confirm it is not empty.

While you are in the operating system, write down the panel's IP address, subnet mask, gateway, device name and OS version. Every later step uses those numbers, and a panel whose settings you did not record is a panel you cannot put back the way you found it.

Free the storage that killed the runtime #

Reported repairs run in escalating order: delete the accumulated alarm log files first; only if the crash returns, clear the runtime's project folders in internal storage and reload the project. The second step deletes the project, which is why it stands behind the USB backup, never in front of it.

Scale the problem before trusting the fix. A data log that appends one 150-byte line every 10 s writes 15 bytes per second and 900 bytes per minute, which is 150 B × 6 records/min × 1,440 min = 1,296,000 B, about 1.3 MB per day, and 1,296,000 B × 365 = 473,040,000 B, about 473 MB across a full year of running. Unbounded logging against fixed internal flash is a countdown, not a strategy.

So bound the generator, or the crash comes back on schedule: configure the log to overwrite its oldest segments, or have the controller delete the oldest records once a count limit is reached.

Stop the runtime before changing the IP address #

Permission Denied. IP setting cannot be change during operation means what it says: the panel locks its network settings while the runtime is running, and putting the HMI into transfer does not unlock them. Stop the runtime from the panel's controls, enter the address, then leave the page and reopen it to confirm the value stored. One safety note: a stopped runtime leaves the operator with no controls, so put the machine in a safe state before you stop it on a running line.

Do not re-address the panel just because the service tool failed to connect. Compare the panel's existing address with the PC's first — if they already share a subnet, the fault is the cable, the adapter or the selected interface, and an unnecessary address change also breaks the panel-to-controller connection the moment the runtime starts again.

Prove the Ethernet path with numbers #

Put the PC adapter and the panel in the same subnet before anything else. The test is arithmetic, not opinion: apply the mask to both addresses and compare the network portions.

Worked example. The PC adapter is set to 192.168.10.10 with mask 255.255.255.0, and the panel reports 192.168.1.20 with mask 255.255.255.0:

  • PC network: 192.168.10.10 AND 255.255.255.0 = 192.168.10.0
  • Panel network: 192.168.1.20 AND 255.255.255.0 = 192.168.1.0
  • 192.168.10.0 and 192.168.1.0 differ, so neither device treats the other as local, and with no gateway on a commissioning link the ping times out and the tool reports it cannot connect to the target device.

Decision: stop the panel runtime and set the panel to an unused address in the PC's subnet — 192.168.10.20 with mask 255.255.255.0 and no gateway on a direct link — then ping 192.168.10.20 from the PC.

Three checks when the ping still fails:

  • Confirm link indication at both Ethernet ports; replace the cable or the switch port if either is dark.
  • Read the panel's address from its operating system, not from an old project file.
  • Check the PC's address-resolution table after the failed ping: a learned MAC entry for the panel proves Layer 2 contact even without an ICMP reply, which points the fault at IP settings rather than the physical link.

In the service tool, select the PC's wired adapter and the plain Ethernet connection method before the PN/IE variant, put the panel in transfer mode, and only then attempt a connection. If the ping succeeds and the transfer still fails, that is a different fault — why an HMI transfer fails in initial start mode despite ping covers it.

The MAC address route and the version ceiling #

When IP-level tools find nothing, the device manual documents an operating-system update in the service tool that connects on the panel's MAC address. It works at the Ethernet layer, so it succeeds with wrong or lost IP settings — but only with the PC and panel on the same switch segment, because a router does not forward that discovery traffic. Use it to recover a panel, not as the routine transfer path.

Check the version ceiling before planning any update. A panel reporting OS V12.0.0.x is a first generation unit, and V12.0.0.x is the last operating system built for that generation; second generation panels run V13.0.0.x up to V17.0.0.x. On a first generation panel there is no newer OS to chase, so the repair is storage and project, not firmware — getting the right firmware file for a legacy HMI panel covers matching files to panels when an update is genuinely available.

The sequence that closes it out #

Run it in this order and the two faults come apart:

  • Back up to USB from the panel operating system and verify the archive on a PC.
  • Record the IP address, subnet mask, gateway, device name and OS version.
  • Delete the accumulated alarm and data logs; reload the project if the folders were cleared.
  • Bound the logging so the storage cannot refill.
  • Stop the runtime, set an unused address in the PC's subnet, reopen the page to confirm it stored.
  • Ping the panel; check link lights and the address-resolution entry.
  • Connect with the plain Ethernet method, panel in transfer mode.
  • Restore the original panel address before the station goes back to the controller.

When to stop repairing #

If the crashes stop after the cleanup and the reload and the logging is bounded, the repair is done. If HMIRTM.EXE keeps dying on a panel already at V12.0.0.x, the ladder is exhausted: no newer OS exists for it, and a runtime that faults after a clean reload points at the hardware. That is a replacement decision — planning an HMI terminal replacement from an older operator panel lays out the criteria — and when the replacement will be PC-based, industrial panel PCs are the category to compare.

Questions asked

Does the HMIRTM.EXE serious error mean the panel is defective?

Usually not. The runtime crashes most often because internal storage filled with accumulated alarm and data logs, or because the runtime data corrupted, and both are repaired on the panel. Treat the hardware as failed only after a USB backup, a storage cleanup and a clean project reload all fail to stop the crashes.

Which OS update should I load on a panel that reports V12.0.0.x?

None. V12.0.0.x identifies a first generation Comfort Panel, and V12.0.0.x is the last operating system built for that generation; second generation panels take V13.0.0.x through V17.0.0.x. The repair on a first generation unit is storage cleanup and a project reload, not a firmware update.

Why does the panel answer Permission Denied when I enter the IP address?

Because the runtime is still in operation, and the panel locks its network settings while it runs. Stopping the runtime releases the lock. The same rule blocks other operating-system settings edited during operation, so whenever a setting refuses to save, check whether the runtime is running first.

Can the backup be done from TIA Portal or ProSave instead of a USB stick?

Not in this state. A transfer needs a working IP path to the panel, which is exactly what has not been proven yet. The backup function built into the panel operating system needs no network and no runtime, which is why it is the first step rather than the last.

What does connecting on the MAC address in ProSave actually get around?

It sidesteps IP addressing entirely: the panel answers at the Ethernet layer, so the method works when the IP settings are wrong or lost. It only reaches panels on the same switch segment, because routers do not forward that traffic, and the device manual documents it for operating-system updates.

Keep reading

  • How-to

    How One Spare HMI Panel Covers Seven Machines

    Yes. Keep one backup archive per machine on a USB stick or memory card, and restore the needed archive to the single spare panel at the panel itself. This works without WinCC flexible only if the backup transfer option was enabled when each project was downloaded; otherwise you need a PC with ProSave, and archives restore only to the same panel model.

    HMI and touchscreens

  • How-to

    How to Upload a Program From an Old Touchscreen HMI

    An editable upload from an old Siemens touchscreen HMI is possible only if Enable back transfer was checked when the project was first downloaded; it was off by default, so most panels refuse. Without it, ProSave recovers at best a binary backup that restores to the same panel type and cannot be edited. Identify the exact model from the label, and ask the original supplier for the project before anything else.

    HMI and touchscreens

  • Troubleshooting

    Getting the Right Firmware File for a Legacy HMI Panel

    Before you chase a firmware file, decide which of three things the panel actually lacks: a communications fix, an application restore, or an operating-system image. A panel that boots and navigates almost never needs firmware, and the only safe source for the image is the manufacturer or an authorized distributor, matched to the exact nameplate model and revision.

    HMI and touchscreens