Troubleshooting
HMI Comms Errors After a PLC IP Address Change
Short answer
An HMI that read tags before a PLC address change and fails after is pointing at its own runtime, not at firmware compatibility. The downloaded application keeps the old controller address unless the transfer replaces communications, and the design path on your computer proves nothing about the runtime target. Verify the shortcut's runtime target and the subnet, re-download with Replace Communications confirmed, and treat firmware only if a corrected path still fails.
On this page
- Why does an HMI stop reading PLC tags right after an IP address change?
- Is this a firmware problem or a stale communication path?
- What does the Replace Communications option change on download?
- Which network settings must match before the HMI can talk at all?
- Why do the design path and the runtime path differ?
- Can you fix the address on the terminal without a new download?
- When does firmware actually become the suspect?
- What is the decision sequence when the HMI reports comms errors after re-addressing?
- Questions asked
An HMI that threw comms errors the moment the machine network moved from 192.168.1.0 to 10.23.40.0 is pointing at its own runtime: the application stored on the terminal still holds the controller's old address. In the reported case a CompactLogix L32E at firmware 16 was replaced by an L33ER at 31 and everything kept working; only the re-addressing broke it. That timing rules out compatibility as the first suspect. The things that actually carry the controller address are the runtime shortcut's target, the terminal's stored communication settings, and the Replace Communications option on the transfer — and RSLinx on your laptop seeing both devices proves your laptop's path, not the panel's. Work the checks below in order and stop at the first one that fails.
Why does an HMI stop reading PLC tags right after an IP address change? #
Because the runtime application on the terminal still holds the old PLC address: a download that does not replace communications leaves the previous shortcut in place, so the panel keeps polling an address that no longer answers and reports comms errors on every screen.
A terminal that talked through the old network stores its own copy of the communication configuration at download time. Re-addressing the PLC and the panel does not reach that stored copy — new addresses on the devices update nothing already written into the runtime. The reported sequence makes this concrete: project upload, runtime restore, path change, rebuild at runtime version 5.1, download — and comms errors on the first screen. Every one of those steps touches files; the only step that rewrites the terminal's stored path is the transfer with communications replaced, and that is where the sequence either succeeds or quietly preserves the old address.
Is this a firmware problem or a stale communication path? #
The timing decides it: an application that read tags at the old addresses and failed only after re-addressing points at the runtime path, because a controller and terminal that talked before the change are by that fact compatible at the level the change touched.
Let the symptom character confirm the call. A stale path fails deterministically: every screen, every tag, the same cannot-reach error, against a device that now lives at a different address. Compatibility trouble behaves differently — values that read wrong, indicators that change color without their text, statuses that flag at random. If the symptom is the first kind, spend the shift on the path. One report does not belong to this case: newer CompactLogix 5069-family controllers are reported to need HMI firmware 10 or later, which excludes some older terminals, but an L33ER is a different family that this same terminal had already served, so that report stays irrelevant until someone changes controller families.
What does the Replace Communications option change on download? #
The Replace Communications option on the transfer tells the terminal to adopt the communication settings defined in the project you are sending; without it the terminal keeps the shortcuts already stored in its current runtime, including a PLC address that predates your network change.
Verify the option on the transfer you are about to run, not on your habit of it. The reported operator believed the box was always checked, yet the failure pattern says the terminal kept its previous communications; the only way to close that possibility is to read the options screen on the next download, because the dialog does not necessarily carry a state from one transfer to the next. A missed checkbox re-imports the terminal's stored configuration, old address included — and if the runtime was restored from an archive that still holds the old shortcut, a download without replacement serves the same stale path from the file side too.
Which network settings must match before the HMI can talk at all? #
Both devices need addresses on the same subnet with matching masks: a PLC at 10.23.40.10 and a terminal at 10.23.40.25, both masked 255.255.255.0, talk directly with an empty gateway, because each device computes the same network, 10.23.40.0, for the other.
Run the arithmetic instead of eyeballing it — AND each address with its mask and compare the networks:
- 10.23.40.10 AND 255.255.255.0 → 10.23.40.0, the PLC's network
- 10.23.40.25 AND 255.255.255.0 → 10.23.40.0, the terminal's network — match, so the empty gateway is correct, not a fault
- 10.23.41.25 AND 255.255.255.0 → 10.23.41.0 — mismatch, so the devices sit on different networks and traffic must route through a gateway or the ping times out
Then confirm the terminal's own address and mask at the panel itself, and that the PLC and HMI addresses stayed distinct — changing one never updates the other. A successful ping from the programming computer validates that computer's interfaces only, and it can even mislead when a second interface owns an overlapping address; a PC whose Wi-Fi holds the address you think you are testing is covered step by step in Why a PC Fails to Reach an HMI When Wi-Fi Owns Its Address.
Safety note: coordinate the address switch with operations, because the panel is blind to the controller from the moment the addresses change until the path is fixed, and a line can keep running with no operator view of its alarms.
Why do the design path and the runtime path differ? #
The project carries two independent communication settings: the design/local path your development computer uses and the runtime target the deployed application uses, so copying pointers from design to runtime only helps if the runtime target itself resolves to the new PLC address.
That is why the reported upload-restore-change-download sequence misleads: the laptop exercised the design path repeatedly and it worked every time. In a FactoryTalk View ME application the screens and tags reference a communication shortcut, and that shortcut holds separate design and runtime targets. Copying pointers from design to runtime target, as the reported operator did, only lands correctly if the runtime target ends up naming the L33ER at its live address — compare the values after the copy instead of trusting the direction of the copy. Before rebuilding anything, open the shortcut the screens use and read the runtime target directly: it should name the controller at its current address, not the one that worked last month.
Can you fix the address on the terminal without a new download? #
Often yes — the terminal's own configuration can carry the correction: in a FactoryTalk View ME Station terminal you can update the device shortcut and device IP at the panel, and on Siemens panels the controller address lives in the HMI connection and is adapted on the panel itself.
This is the quick route when the only change is the controller's address: set the new PLC address over Ethernet, then edit the shortcut's target in the terminal's configuration rather than rebuilding the runtime, which leaves the running application untouched. Two limits keep it from being the whole answer. It fixes the deployed runtime but not the project, so bring the project's runtime target to the same address in the same session — the next download without replacement re-imports whatever the project still holds.
And it does not scale: a re-addressing that touches drives, remote I/O or a second controller leaves some device unedited, and the missed one becomes next month's mystery fault. When you do rebuild, create the runtime in the version the terminal's firmware actually runs, because a mismatch fails the transfer before communications are ever tested — Fixing an HMI MER runtime version mismatch walks through that failure.
When does firmware actually become the suspect? #
Only after the path checks out: if the runtime shortcut points at the live controller address, the transfer replaced communications, and the subnet check passes yet errors persist, then compare terminal firmware against the controller family using the vendor's release notes for the exact catalog number.
For the PanelView Plus 600 in the reported case, catalog number 2711P-T6C20D, the labels 5.10.16UP and 5.10.16.9 both circulate as the firmware ceiling; they are not interchangeable, and neither becomes a decision until you read the release notes of the package published for that exact catalog number — the notes also identify the embedded FactoryTalk Linx version, which is what a controller-side change must be tested against.
A widely repeated claim places a change in how Logix controllers handle Class 3 HMI traffic around controller firmware 24 and pairs it with a FactoryTalk Linx minimum of 6.00; treat it as a lead to verify in those notes, not as a requirement. The documented anchor: Logix 5000 controllers reserve a dedicated Class 3 pool for HMI and message-instruction connections, up to 768 connections split 384 incoming and 384 outgoing — your panel's polls live in that pool, so a terminal that cannot establish its Class 3 connection reports comms errors while everything else on the network looks healthy.
If the notes show the ceiling cannot support the controller you are moving to, the path fixes are done and the honest call is replacing the terminal; a PC-based operator station running your visualization software from the industrial panel PCs catalog takes the terminal's place at the machine when the repair is not worth pursuing.
What is the decision sequence when the HMI reports comms errors after re-addressing? #
Work the list in order and stop at the first failing step: network and subnet, terminal-side address, runtime shortcut target, Replace Communications on transfer, project-versus-terminal consistency, and only then firmware compatibility against the controller family.
- Record the current address and mask of every device you moved — controller, panel, anything between them — and run the subnet AND test above; a matched network keeps the gateway field empty, a mismatched one needs a gateway.
- Ping each device from the programming computer and refresh the browse list so a cached entry cannot fake success.
- At the terminal, confirm the terminal's own address and mask, and that controller and panel addresses remain distinct.
- In the project, read the communication shortcut's runtime target and confirm it names the controller at its live address; check the design/local path separately.
- Rebuild the runtime at the version the terminal runs and download with Replace Communications confirmed on that transfer dialog.
- If a verified path still fails, compare the terminal's firmware against the controller family in the release notes for the exact catalog number, and plan the replacement if the ceiling blocks the combination.
The decision, stated once: when tags read at the old addresses and failed only after re-addressing, the fault is the runtime path until a shortcut target naming the live controller, a Replace Communications download and a passing subnet test have all failed together. Firmware enters only after that triple failure, and then through release notes for the exact catalog number — not through symptoms alone. For the reported L32E-to-L33ER upgrade with the full network move, that order puts items 4 and 5 at the top of the suspect list and leaves the firmware ceiling as a verification, not a cause.
Questions asked
How do I confirm which controller address the runtime is actually polling?
Read the diagnostics the runtime itself shows. FactoryTalk View ME stations list failed connections with the device or shortcut involved, and many other platforms print the unreachable address in the error banner or diagnostics page. Compare what that message names against the controller's live address: if the failing target shows the old 192.168.1.0 network, the stored path is stale; if it names the new address and still fails, move on to masks, gateways and link quality. That one comparison separates a stale shortcut from a genuine network fault in seconds.
Can a wrong subnet mask look exactly like a stale runtime address?
Yes, the panel reports the same comms errors either way. The distinguishing test is who else fails: if the programming computer's tools also lose the controller, the fault is network-level, typically a mask or gateway entered during the re-addressing; if only the panel fails while your laptop reads tags, the stored runtime path is the suspect. Fix the mask case in the device network settings, the path case in the shortcut and the download, and re-test tag reads at the panel before closing the job.
Does changing the controller's IP address require changes in the PLC program?
No. The address lives in the controller's network settings, so logic, tags and routines transfer untouched, and nothing in the program references the address. What breaks are the clients that stored the old one: the HMI runtime, SCADA servers, historians, peer controllers with message instructions, and drive or I/O configurations pointing at the controller. Update every stored reference in the same outage, because each one you leave behind becomes an independent comms fault with an identical symptom at its own device.
What should I record before re-addressing a machine network so I can roll back?
Write down, per device, the old and new address, mask and gateway, plus the communication shortcut names and their targets in the HMI project and the runtime version installed on each panel. Photograph the controller's current network settings before touching them. With that record, a failed re-address is a ten-minute revert on one device; without it, a stuck line during production hours turns into archaeology under time pressure. Keep the sheet with the machine's panel schedule so the next technician inherits it.