How-to
How to Identify an Unbranded Legacy Touch Panel Before Replacing It
Short answer
Identify the panel from its rear nameplate: photograph it, record the full model text including the suffix, and match it to the exact model's documentation. A 24 VOLT marking and a matching screen size establish nothing about model, driver, cable, or cutout compatibility, and two look-alike panels from one family are not interchangeable.
On this page
- The identification procedure, step by step
- What the running screen still tells you
- Read the rear nameplate and record every character
- Match the model text against the exact model's documentation
- Worked example: the same diagonal, a different cutout
- Communication, supply, and mounting: three checks that fail independently
- The decision
- Questions asked
You identify an unbranded legacy touch panel from its rear nameplate, not from its front appearance. Photograph the nameplate, copy the full model text exactly as printed — every suffix, revision, and serial digit — and match that text against the manufacturer's documentation for that exact model before anything is ordered. Terminal markings such as 24 VOLT, COM 1, COM 2, and DIF LPT document the wiring; they do not identify the model. A 24 VOLT supply marking and a screen of the same size establish nothing about driver, cable, or cutout compatibility, and two panels that share a family look are not interchangeable. Identification is finished only when the documented model's interfaces, supply, and mounting dimensions each match what is installed in the cabinet.
The identification procedure, step by step #
- Photograph every operating and alarm page the panel still displays, without changing production settings, and note which values update and which stay fixed.
- Locate the project or source file if the machine builder stored one, and read the target model named in its settings.
- Photograph the front, rear, nameplate, connectors, and cable labels before the unit is removed.
- Record the full model text from the nameplate, including the suffix, together with the revision and serial number.
- Record terminal markings exactly as printed, including abbreviations whose meaning you cannot confirm.
- Match the full model text against documentation for that exact model, not for a similar model in the same family.
- Compare the documented communication interfaces with the installed cable and the controller port: electrical standard, pin assignment, driver.
- Read the supply specification from the unit's own label and manual, then measure the voltage at the panel terminals under load.
- Measure the cabinet cutout, rear depth, and cable clearance, and compare them with the model's mounting drawing.
- Order only against the confirmed model data, and verify the exact part number first.
What the running screen still tells you #
An unfamiliar enclosure is an identification problem, not a communication fault, and a blank or dim display does not identify the model either. Treat the panel's condition and the panel's identity as two separate questions.
While the unit still runs, record what the application knows: page names, displayed units, alarm text, the commands the operators use, and the difference between a value that changes with the process and one that stays fixed. Those photographs preserve information the rear label cannot give you, and they define what a replacement has to reproduce.
If the machine builder left a project or source file on disk, reading an old HMI program before panel replacement is the fastest route, because the file's target setting names the exact model the application was built for. A stored file names a model; it does not prove that file is what is loaded in the panel, so the nameplate check still stands.
Read the rear nameplate and record every character #
Copy the full model text character by character. On panels of this generation, a suffix such as -STN marks the display variant, and the same base number with a different suffix can carry different port electronics and a different user-memory figure. Record the revision and serial number beside the model text, and photograph the connector arrangement and every cable label before anything is unplugged.
Terminal markings are wiring facts, not identification. One unidentified unit of this kind carried 24 VOLT, COM 1, COM 2, and DIF LPT next to its connectors. The first three document the supply and the two serial ports. DIF LPT is recorded exactly as printed, because a familiar-looking abbreviation is not a basis for assigning a connector function. None of the four markings identifies the model, and none of them transfers to a replacement: pin assignments come from the identified model's documentation, not from screw-terminal labels.
Match the model text against the exact model's documentation #
Manufacturers' manual download pages search on the full model text with its suffix, so a legible nameplate resolves the port list, the supply range, and the mounting drawing in one pass. Match the text to that model only. A 5.7-inch STN model and an earlier model from the same family can share the bezel look, the supply marking, and the connector style, and still differ in ports, memory, and mounting, which is why the two are not interchangeable even as an emergency swap.
Interchangeability is decided by five separate facts — model, driver, cable pin assignment, supply range, and mounting cutout — and passing one proves nothing about the next.
| Observation | It establishes | It does not establish |
|---|---|---|
| 24 VOLT marking | Nominal supply class | Permitted range, polarity, consumption |
| 5.7-inch screen | Display diagonal | Enclosure size, cutout, rear depth |
| COM 1 and COM 2 labels | Two serial ports exist | Electrical standard, pin assignment, driver |
| Family bezel look | Same product family | Model identity, port electronics, memory |
| -STN suffix | Display variant of that base number | Compatibility with other suffix variants |
The documentation also settles user memory. The specification sheet for one documented 5.7-inch STN panel of this generation lists 1 MB of flash EPROM with 640 KB for user projects: 1024 − 640 = 384 KB stays with the firmware, so a captured application estimated at 700 KB exceeds the 640 KB figure by 40 KB and does not load into that variant.
Worked example: the same diagonal, a different cutout #
Example inputs, labeled as such: a documented 5.7-inch, 320 × 240 panel specification; a measured cabinet opening of 162 mm × 128 mm; a required cutout of 165 mm × 131 mm taken from that model's installation manual for this example.
- Display diagonal: 5.7 in × 25.4 mm/in = 144.8 mm.
- Active area at 4:3 aspect: width = 144.8 mm × 4/5 = 115.8 mm; height = 144.8 mm × 3/5 = 86.9 mm.
- Cutout comparison: 165 mm − 162 mm = 3 mm short in width; 131 mm − 128 mm = 3 mm short in height.
Decision: the identified model does not seat in the existing opening. Either the door is machined to the manual's cutout or a model with a smaller mounting requirement is selected. The diagonal made no contribution to that answer: 144.8 mm of display glass says nothing about a 165 × 131 mm hole until the mounting drawing connects them.
Communication, supply, and mounting: three checks that fail independently #
Communication first. Match the electrical standard on the port you actually use — RS-232, RS-485, and RS-422 are not interchangeable — then the pin assignment of the installed cable, then the driver in the replacement's engineering software for your controller. A panel with no driver for your controller is disqualified regardless of fit; see when the HMI software has no driver for your PLC.
Supply next. The 24 VOLT marking is a nominal clue, not a specification: read the permitted range, polarity, and consumption from the identified unit's documentation, then, with the machine in a safe maintenance state, measure at the panel terminals while the panel is working — adequate voltage at an unloaded supply can still drop through the wiring under load.
Mounting last. Measure the cutout, the rear depth, and the cable clearance, and compare them with the model's mounting drawing; when the replacement has to fit the existing opening, take the panel cut-out reference dimensions into that comparison.
The decision #
- Nameplate readable and documentation found for the exact model text: the panel is identified. Run the driver, supply, and cutout checks against that documentation, then verify an obsolete HMI replacement before ordering.
- Nameplate missing or unreadable: identification moves to the manufacturer or an authorized distributor with your photographs. Order nothing against a guess.
- A look-alike candidate with the same screen size and supply marking but no documentation match on ports, memory, or cutout: rejected. Same size is not the same model.
- A stored project file whose target model contradicts the nameplate: the nameplate wins. The file says what was built; the label says what is installed.
Questions asked
The rear nameplate is missing or painted over. How do I identify the panel?
Photograph the front, the rear, the connector arrangement, and any board-level markings you can see without opening the unit, and send them to the manufacturer or an authorized distributor; support channels identify legacy models from enclosure and connector photos. In parallel, check the machine builder's electrical drawings and the original purchase records, which usually list the exact part number ordered.
What can a suffix such as -STN actually change between two panels with the same base number?
On panels of this generation the suffix selects the hardware variant: display technology, and on some families the port electronics and the user-memory figure. Two units that share a base number but carry different suffixes can need different drivers, cables, and firmware, and a project built for one variant may not load into the other. Match documentation to the full model text, suffix included.
How much rear depth should I allow for the replacement panel?
Take the depth figure from the identified model's installation drawing, then add room for the deepest connector, its cable bend radius, and a service loop. A depth quoted without connectors is not usable, because serial and power connectors with strain relief commonly stand taller than the enclosure rear. Measure the clear space behind the opening, including any DIN rail or wire duct in the path.
Can the programming cable found in the cabinet identify the panel?
Only weakly. Cable families are shared across several models, so a found cable narrows the software family at best, and cabinets accumulate replacement cables that fit mechanically without matching the original pinout. Treat the cable as a lead and confirm from the nameplate, or from the target model named in a stored project file, before ordering anything.