How-to
How to Remove a Bonded HMI Touchscreen Glass From the Bezel
Short answer
The glass is held only by adhesive around the full perimeter of the bezel, so warm the edges with a heat gun on low until the surface reaches about 38 to 43 °C, then open the bond in small increments with a thin, non-marring tool. Never force a cold or cracked assembly, and clean the bonding land flat before seating the replacement glass.
On this page
The glass is still in the bezel because it is glued around the full perimeter of the plastic housing — nothing else is holding it once the circuit board is out. Warm the edges with a heat gun on its lowest effective setting until the surface reaches roughly 38 to 43 °C, keep the nozzle moving, and open the bond in small increments with a thin, non-marring tool. Force is the failure mode here: pulling a cold or cracked assembly concentrates the load in brittle glass, and that is how a repairable panel gets destroyed.
Why the glass will not lift out #
Removing the electronics ends the mechanical work; what remains is a glue joint. The adhesive runs around all four edges of the housing, which is why the center of a cracked glass can flex while the border stays fixed. More pulling does not address that joint — it addresses the glass.
One handling rule carries the real risk in this job: cover a cracked face with tape or removable film so fragments stay captured, wear eye and hand protection, and keep the face pointed away from you while any force is applied. A pane that looks stable can separate the moment one edge lifts.
| Move | What it does |
|---|---|
| Pulling harder on one corner after the board is out | Concentrates the load in already-cracked glass |
| Prying while the perimeter is cold | Transfers pry force into the glass and the bezel |
| Holding the nozzle over one spot | Releases one point unevenly and distorts nearby plastic |
| Ordering a replacement by display size alone | Buys a sensor or connector arrangement that does not fit |
Prepare the terminal and the replacement #
- Disconnect power and follow the machine's isolation procedure before opening the terminal. A dark screen does not prove every supplied circuit is de-energized.
- Record the complete catalog number from the terminal label. Different HMI variants use different screen assemblies, so display size alone does not identify the part — planning an HMI terminal replacement covers those identity checks before you commit to a part.
- Photograph connector orientation, cable routing, shields, spacers and hardware before disconnecting anything.
- Remove the board and any components needed to expose the rear of the bonded front assembly. Store screws by position, not in one pile.
- Move the removed electronics away from the heating area and protect them from static discharge and glass debris.
- Compare the replacement against the original before you separate anything: dimensions, active-area orientation, connector type, cable exit direction and mounting features. If any of those do not match, stop — a physically similar part can still carry a different touch interface or cable arrangement.
Release the glass with controlled heat #
- Lay the front assembly on a stable surface that supports the bezel without pressing on the broken viewing area.
- Set the heat gun to its lowest effective setting — warm enough that the edge surface reaches about 38 to 43 °C (100 to 110 °F), the band documented for softening this class of bezel adhesive on operator-terminal fronts.
- Warm one perimeter section with continuous motion, including the corners; the adhesive is thickest at the edges and runs around them.
- Test the warmed edge with a thin, non-marring tool such as a plastic pick, using only enough force to feel whether the bond has softened.
- If the edge holds, withdraw the tool and make another heating pass. Do not trade heat for force.
- When a gap opens, hold it with a thin spacer and advance along the edge in small increments instead of lifting the whole side.
- Work around the housing the same way, reheating any section that starts to resist again.
- Support the glass as the last bonded area lets go, and lift it out without twisting the final attached corner.
- Watch the plastic the whole time. Any softening, distortion, discoloration or surface-texture change means stop heating and let the assembly cool.
Warming a 600-class perimeter at 38 to 43 °C #
The case from the bench: a PanelView Plus 600 with a shattered touch glass, the electronics already removed, and a heat gun on the bench. Work the numbers before the first pass.
Inputs:
- Adhesive softening band: 100 to 110 °F at the surface, the documented figure for heat-gun-low softening of this adhesive class.
- Warming time that softens an edge: about 1 to 2 minutes of moving warm air.
- Perimeter: four sides, with the adhesive continuous around the corners.
Rule in words: convert the documented band to working units, then divide the documented warming time equally across the four sides, corners shared between neighbors.
Arithmetic:
- °C = (°F − 32) × 5/9. (100 − 32) × 5/9 = 68 × 5/9 = 37.8 °C. (110 − 32) × 5/9 = 78 × 5/9 = 43.3 °C. Working band: 38 to 43 °C.
- Time per side: 60 s ÷ 4 sides = 15 s per side at the fast end; 120 s ÷ 4 = 30 s per side at the slow end. One full pass around the housing therefore takes 1 to 2 minutes, which matches the documented warming time.
Result: run 15 to 30 seconds of continuous nozzle motion per side, corners included, then test that side with the pick before moving to the next.
Decision: two full passes is the cutoff — 2 × 60 s = 120 s to 2 × 120 s = 240 s, so 2 to 4 minutes of cumulative warming. If every edge still refuses to open after two passes, the heat is not reaching the adhesive: shorten the distance or raise the airflow slightly and repeat. Do not add pry force. Stay inside the band while you do it, because glass taken well past 43 °C can crack as it cools from thermal stress, and the bezel plastic distorts long before the glue burns. A hair dryer lands in the same band, just more slowly.
Clean the bezel and seat the new glass #
- Collect every loose fragment before handling the bezel further.
- Inspect the bonding land where the adhesive sat: chips, raised residue, distortion or pry damage. The replacement needs a flat, clean seating surface.
- Remove residual adhesive without gouging the plastic, keeping debris and cleaning material away from the visible area and any flex connector. Use only materials compatible with the housing and the viewing surface — an unverified solvent can haze the front or attack the plastic.
- Dry-fit the replacement before exposing or applying its adhesive. Confirm orientation and cable reach without folding or tensioning the flex tail.
- Route the cable exactly as photographed, clear of screw bosses, board edges and anything the housing compresses.
- Seat the glass evenly around the perimeter. Do not press at the center to close an uneven edge.
- Do not finalize the bond until fit and cable orientation are confirmed. Repositioning a bonded assembly cracks it, contaminates the adhesive or leaves an edge lifted.
Verify the repair before the terminal goes back #
- Bench-test before reinstalling if your work controls allow it. Watch the first power-up and remove power on any abnormal heating, smell, smoke, display artifact or instability.
- Confirm the display starts and stays visible: no flicker, no missing areas, no pressure marks. A screen that stays dark after this work is a separate fault — troubleshooting a panel PC HMI dark screen after reboot walks that path.
- Test touch response across the full active area, especially the corners and the edges you released.
- Confirm the indicated position matches the point pressed. If it lands offset, run the terminal's touch calibration routine — on most operator terminals that lives behind the configuration menu, and entering configuration mode on a touch HMI gets you there.
- Inspect the perimeter one last time for lifted sections, uneven seating, trapped debris or bezel distortion before the terminal goes back in the panel.
Questions asked
Can a hair dryer substitute for a heat gun on this job?
Yes. The method is gentle warm air at the edges, and a hair dryer delivers that with less risk of overheating the plastic. Expect to spend the full one to two minutes per pass rather than less, and hold the dryer closer than a heat gun nozzle would sit because the air arrives cooler. Stop and let the assembly cool if the bezel softens, distorts or changes surface texture.
How do I know the edge is at the right temperature without an instrument?
An edge in the 38 to 43 °C band is briefly touchable, so rest a fingertip on the warmed plastic for a second: if you cannot hold it there at all, back the heat off. That band softens the adhesive without the risks on either side, an uneven release from cold glue, or thermal stress in the glass as it cools after overheating. The bezel plastic is the hard ceiling either way.
Does the touch screen need recalibration after the glass is replaced?
Check it rather than assume. Press-test the corners and the edges near the released perimeter first; if the indicated position tracks your finger or stylus everywhere, calibration can wait. If the touch point lands offset across the whole area, run the terminal's touch calibration routine. Offset only near the edges with a good center points to debris or an uneven seat under the perimeter, not calibration.
Does the replacement glass come with adhesive, or do I supply it?
Replacement touch-glass assemblies for these terminals typically ship with adhesive film already on the rear perimeter. Keep the release liner on until the dry fit passes, then peel and seat in one motion. If a part arrives bare, use a thin perimeter tape rated for the housing plastic rather than dots of liquid glue, so the bond line stays even and the glass sits flat across the whole land.