HMI and touchscreens
Earlier articles
How-to
How to Rotate a 3D Object on a Touch Panel With Drag Input
Leave the camera fixed and rotate the object: map each drag to a rotation delta at 0.3 degrees per pixel and compose it onto the object's current orientation as a quaternion, around a pivot at its center. Only the object transform changes per drag, so no camera up-vector or translation is ever recalculated.
How-to
Building a complete on-screen keyboard from bitmap HMI assets
Start from the terminal vendor's most complete keyboard demo, not a blank bitmap: the demo already carries the key-state and editing logic, so you extend its key map, replace the artwork, and adjust its macros to a written character specification. Then verify three things separately: the characters shown, the character each touch delivers, and the value the receiving application accepts.
How-to
Connecting an HMI panel to an S7-300 MPI port with a PG
Yes: wire the panel's RS-485 port to the CPU's MPI/DP port and run the Siemens S7 MPI driver, with no communication module. Put a PROFIBUS connector with a PG socket on that port, hang the PC adapter on the socket, give every node a unique address and one common baud rate, and STEP 7 stays online while the panel runs.
Explainer
What a SCADA Operator Interface Must Do: Core Functions
A SCADA operator interface carries six functions: acquisition and display of binary and analog data, alarm and event recording, a history database of process values, measurand processing for derived values, presentation through graphics, lists and reports, and command handling from binary commands to recipes. Keep alarm and event records separate from the history database: one records occurrences, the other retains values.
Selection guide
Do You Need SCADA Software for a Modbus HMI Project
No. Modbus only proves a possible data link, so pick the runtime target first: a touch panel programmed by its own editor for machine-side parameter control, or a licensed PC SCADA runtime when the screens must run on a computer. The documented demonstration mode of a Vijeo Citect-class runtime stops after about 15 minutes with live devices, which settles a bench test but not continuous operation.
Selection guide
Running an Ignition Vision Client as a Machine HMI Without Edge
No Edge license is needed. A Vision client at the machine is one more client session of your existing on-site gateway, so the only check is whether that gateway's license counts clients. Edge is a separate device-level gateway for machines that must keep running with the site link down; your panel HMI stays as the OPC UA server either way.
Troubleshooting
Why PanelBuilder32 Cannot Reach a PanelView 1000 Over Ethernet
The PanelView-to-controller session proves only the runtime path; PanelBuilder32 needs its own route to the terminal. Read the terminal's IP address, subnet mask, and RS-232 port assignment from configuration mode — on a touch-only unit, the filled box at the lower-right during startup — before swapping cables, because a port assigned to printer-only duty never accepts a transfer.
How-to
Convert an Old MER File to FactoryTalk View 13
Renaming a v4.0 .mer or picking a newer runtime in Studio converts nothing: the documented path is restoring the runtime in FactoryTalk View Studio, auditing what came back, and rebuilding what did not. Plan for alarm messages to be lost on a v4.0 restore.
Troubleshooting
Why an HMI sends email in simulation but not from the panel
Email that leaves from PC simulation but never from the physical panel means the project logic works and the panel's own send path is broken. Work the panel's chain in order: count and send condition, gateway, DNS and mail-server reachability, then the deployed project's email options, changing one option at a time. In the case behind this pattern, one checked option in the panel's email settings was the entire fault.
Troubleshooting
When an M580 Downloads but Sends No Data to the HMI
Both projects download because programming access and runtime data access are separate channels out of the CPU. On Control Expert v16.x, Engineering Link Mode set to Enforced in the Security tab refuses the HMI's reads while downloads still succeed, and a Data Dictionary enabled after the last build never delivers the symbols. Set Full Access, do a full rebuild, download, and confirm the Data Dictionary was on before that rebuild; a force test in RUN proves it.
How-to
How to Split Modbus Register Bytes in Operator Terminal Expert
Create a variable of type USINT with array size 2 on each register: Operator Terminal Expert assigns the register's low and high byte addresses to the two elements. Rebuild a 16-bit field split across two registers as low byte + 256 × high byte into a UINT, and write it back by replacing only that field's bytes while preserving the neighbor in the shared register.
Troubleshooting
Fixing Modbus TCP Addressing Errors Between an HMI and a PLC
An HMI 'device not found' alarm over Modbus TCP usually means the panel sent a request outside the PLC's mapped registers, not that the network is down. Convert the PLC's byte offsets to register addresses with HMI address = 40000 + byte offset / 2, so a REAL at 100.32 becomes 40016 and 100.36 becomes 40018, and allocate booleans from 100.16 so the driver's grouped 16-bit read stays inside the mapped base.