Explainer
Portrait HMI Panel Mounting and Temperature Derating Explained
Short answer
No. Portrait mounting does not derate an HMI panel's temperature rating — the vendor's release information for the panels that gained portrait mode states the landscape specifications continue to apply, because rotation in the screen's own plane leaves tilt, convection and dissipation unchanged. The derating that still governs is mounting angle: the 15-inch model's angle table reads the same row in portrait as in landscape.
On this page
No. Rotating an HMI panel 90 degrees into portrait does not derate its temperature rating. The release information for C-more programming software version 6.70, which added portrait orientation to the EA9 panels, states that portrait mode does not derate the panels' temperature ratings and that the specifications published for landscape continue to apply. The physics agrees with the paperwork: a panel's thermal limit is governed by its tilt from vertical, and rotating the screen in its own plane leaves the tilt, the convection path behind the electronics, and the dissipated watts exactly where they were. What does move the number is mounting angle — the 15-inch EA9 manual documents temperature derating by mounting angle — and that table governs a portrait install exactly as it governs a landscape one, because the tilt has not changed.
Portrait rotation is not a thermal variable #
Three things set how hot an HMI panel runs: the watts it dissipates, the ambient air behind it, and how freely that air moves. Portrait rotation changes none of them. The backlight, driver board and power supply see the same load; the enclosure air is the same air; and natural convection across the rear of the panel depends on the panel's lean from vertical, not on which edge points up. Rotating about the axis sticking straight out of the glass sends the same heat through the same path.
That is why the answer to the portrait question is a flat no for the EA9 family: the orientation is a display configuration, not a thermal condition, and the hardware specification printed in the manual did not gain a new column when the software gained a new mode. There is no portrait temperature setting to hunt for — the limits are printed specifications, not configuration values. Software cannot derate hardware; the only documented derating for these panels is the mounting-angle table, and it is keyed to tilt.
The habit is industry-wide. Panel PC manuals carry the same style of guidance — the ASEM 6300P user manual, for example, rates power consumption at 156 W maximum and directs the installer to consider the working temperature and the power supply's thermal derating. Wherever a display and a power supply share a sealed box, the manual tells you what its numbers assume.
The angle table is the derating that matters #
As a panel leans back from vertical, buoyant air does progressively worse work sweeping the rear surface, and at horizontal it simply pools behind the electronics. Angle-derating tables express that as bands: within so many degrees of vertical you get the full range, and each tilt band beyond it subtracts from the top of the range. The 15-inch EA9 manual carries such a table, written around landscape mounting — but the variable it keys on, tilt from vertical, is the same variable in portrait. Measure the angle between the panel's rear face and a plumb line, and look up that row whichever way the screen is rotated.
Where a manual lists no angle table, the published range applies to the mounting positions the manual documents — usually a band either side of vertical. A position the manual does not document is outside the specification; there is no unstated margin to spend. Commit to the documented window.
Worked example: a tilted panel in a sealed enclosure #
The table values are model-specific, so treat the numbers below as an illustration of the method, not as EA9 data. Assume:
- Panel specification in the style of the EA9 table: 0 to 50 °C mounted within 10° of vertical; 0 to 40 °C at 30° of tilt.
- Panel dissipation: 30 W.
- Sealed steel enclosure, thermal resistance from its datasheet: 0.6 °C/W.
- Plant ambient: 30 °C.
The arithmetic:
- Heat rise inside the enclosure: 30 W × 0.6 °C/W = 18 °C.
- Air the panel breathes: 30 °C + 18 °C = 48 °C.
- Mounted vertical: 48 °C against the 50 °C limit — 2 °C of margin. It passes.
- Tilted 30°: 48 °C against the 40 °C limit — over by 8 °C. It fails.
- To run tilted at all, the allowed rise is 40 °C − 30 °C = 10 °C, so the enclosure must reach 10 °C ÷ 30 W = 0.33 °C/W.
Decision for this case: mount it vertical, or move to a larger or air-conditioned enclosure before tilting. Do not drill vents into a sealed enclosure to buy the margin back — the holes change more than the thermal resistance, they end the environmental rating the enclosure was installed to keep. Portrait or landscape appears nowhere in the arithmetic; tilt and enclosure rise are the whole story. Run the same method with your model's real table values and your enclosure's real thermal resistance.
Setting orientation without losing touch alignment #
Orientation is set on the panel, not just drawn in the project. On a PanelView 800 the documented path is Terminal Setting --> Display --> Orientation, then select the degrees required. Panels that reach their setup screens at power-up follow the same pattern; the steps for entering configuration mode on a touch HMI cover that entry. Screens designed for landscape will letterbox or misplace objects if the panel side is left alone, so set the project aspect and the panel orientation together.
Then verify touch: taps at the four corners should land true, and if they land rotated or offset, run the touch recalibration the panel offers before release. Resistive digitizers in particular keep their own coordinate map. The same job on a Siemens KTP-400, rotating an HMI screen from portrait to landscape, walks through the panel-side settings for that family.
Sealing, clamps and the cut-out #
Rotation changes nothing in the seal. The gasket seats on the same cut-out, and the ingress rating depends on gasket compression, cut-out flatness, the torque pattern and the gland ratings — installation conditions, not orientation. What portrait does change mechanically is which clamps carry the panel's weight: gravity still points down, and in the rotated install it loads different bracket edges. Fit the mounting brackets and clamp screws in the orientation the installation sheet shows.
If it is the console's tilt that is costing you the derating, moving the station to a flush door mount keeps the tilt at zero; embedded panel-mount PCs are the class built for exactly that cut-out mounting.
The decision #
- EA9 panel into portrait: no derating. Mount it; the landscape specification stands.
- Any panel tilted in a console: the angle table governs. Measure tilt from vertical and design against that row's limit, portrait or landscape.
- Enclosure running close: run the heat balance against the derated limit, and tilt only when the rise fits the lower number.
- No angle table in the manual: the stated range covers the documented mounting positions only; mount inside them or get the vendor's tilt guidance in writing.
- Layout forcing a redesign rather than a rotation: planning an HMI terminal replacement from an older operator panel covers the sizing, cut-out and software steps.
Questions asked
Does portrait mounting change the panel's IP rating?
No. The front gasket seats on the same cut-out either way, so the ingress rating depends on gasket compression, cut-out flatness, the clamp torque pattern and the cable-gland ratings — installation conditions, not screen rotation. Keep the documented glands and torque values and the rotation itself costs you nothing; sealing is decided by how the assembly is installed, not by its orientation.
Do older projects support portrait after the software upgrade?
Portrait orientation arrived with version 6.70 of the C-more programming software, so a project has to be opened and published from that version before portrait screens exist; earlier versions have no orientation option to set. Upgrade the engineering workstation first, then set the panel orientation on the target hardware, and retest touch alignment there before you call it done.
Does portrait operation increase the panel's heat?
No. Rotation redraws the same backlight and electronics at the same brightness, so dissipation is set by backlight level, processor load and supply efficiency — not by which edge is up. If a hot enclosure needs a few watts back, lowering backlight brightness is the one operator-level setting that measurably reduces panel heat, and it works the same in either orientation.
Our panel's manual has no mounting-angle table. Can we tilt it anyway?
It means the published range applies to the mounting positions the manual documents — typically a band either side of vertical — and any position outside those is outside the specification, not covered by unstated margin. If the console tilts the panel beyond that window, either get the vendor's tilt guidance in writing or redesign the mount to sit vertical; do not spend margin you cannot find in print.