Selection guide
Selecting a Rear-Panel Mount HMI for Machine Fascia Installation
Short answer
Order the model the manufacturer explicitly lists for rear-panel (open-frame) mounting — Weintek's 7-inch MT8070iER rather than the framed MT8070iE — then verify cut-out, mounting points, panel thickness, rear clearance and gasket sealing against the dimensioned drawing before the fascia is cut. Screen size never sets the opening; the drawing does.
On this page
- Order the variant the catalog lists for rear-panel mounting
- What the dimensioned drawing must settle before the fascia is cut
- Cut-out dimensions belong to the model, not the screen
- Worked example: a 7-inch rear-mount terminal against a 175 x 132.5 mm opening
- Sealing, panel thickness and retention
- Same platform, but verify the download target
- Accept the terminal in the finished fascia
- Questions asked
Order the rear-panel variant the catalog lists by order code: Weintek's 7-inch MT8070iER, programmed with EasyBuilder Pro, is the frameless rear-mount item, and the framed MT8070iE is not an acceptable substitute behind a fascia. After that the selection work is mechanical, not software: cut-out, mounting points, panel thickness range, rear clearance and sealing all come from the dimensioned drawing for the exact order code and get verified against the fascia before anything is cut. Screen size sets none of those dimensions — one documented 7-inch terminal needs a 175 x 132.5 mm opening while its screen diagonal is only 177.8 mm.
Order the variant the catalog lists for rear-panel mounting #
Rear-panel mounting means the terminal lives behind the fascia: the machine panel carries the visible front, and the terminal mounts from behind with its own retention. An open-frame (frameless) unit is built for this — it arrives without a finished front housing of its own, so the fascia defines the presentation. Manufacturers sell this as a distinct order code, not as an installation technique you apply to any panel. In the Weintek range the 7-inch frameless rear-mount item is the MT8070iER, programmed with EasyBuilder Pro, with the framed MT8070iE as its counterpart on the same platform. Same screen, same software — the mounting interface is the difference you are buying.
Mounting style stays a per-model catalog fact. The same manufacturer's 21.5-inch cMT3218XP is documented for both panel-mount and VESA-arm installation, and neither option transfers to another model by analogy. So the first line of the purchase specification is the exact order code with rear-panel mounting stated, and the framed equivalent is not an acceptable substitute — it leaves the mechanical interface undefined. If this selection is part of a wider retrofit, hold the same line when planning an HMI terminal replacement from an older operator panel.
What the dimensioned drawing must settle before the fascia is cut #
Demand the dimensioned drawing and the installation instructions for the exact order code, and make them answer every row of this table before the fascia is machined.
| Check | What the document must state | Decision rule |
|---|---|---|
| Mounting style | The exact order code is listed for rear-panel (open-frame) mounting | Not listed for it: wrong model for this job |
| Cut-out | Opening width and height, with tolerances and any corner detail | Any dimension outside the machined opening: re-select or re-machine |
| Mounting points | Hole spacing and the retention method (clips, brackets or studs) | The fascia carries the documented retention, nothing improvised |
| Panel thickness | Minimum and maximum fascia thickness for correct gasket compression | Fascia outside the band: change the material or the model |
| Rear clearance | Housing depth plus connector projections, from the rear view | Less than depth plus connector and service space: move the layout |
| Sealing | Gasket position and the installation conditions attached to the front rating | Gasket not fully supported by the fascia: the rating does not transfer |
| Environment | Operating temperature and vibration for the mounted orientation | Fascia environment outside the datasheet limits: different model |
| Engineering tool | The software supports the exact model as a target | Target not selectable: the project cannot transfer as it stands |
None of this comes from a product photograph or a screen size; every value is a drawing dimension or a stated installation condition. The same drawing-first rule decides servo mount compatibility decided from dimensioned drawings on the drive side of the machine: if the dimensioned drawing does not state it, it is not specified.
Cut-out dimensions belong to the model, not the screen #
Cut-out dimensions are model properties. One documented 7-inch panel-mount terminal, the IPT2070-WST4B, lists a 175 x 132.5 mm cut-out and is noted as compatible with the PT070 cut-out family — that compatibility note is worth more than any screen-size arithmetic, because it is what lets a replacement drop into an existing opening without re-machining. Where the fascia opening already exists, lay the candidate's drawing against a panel cut-out reference before ordering, not after. And keep the visible rectangle and the sealed rectangle separate — the opening-versus-bezel relationship is the same discipline as selecting a thin-bezel industrial HMI display for a cut-out.
Worked example: a 7-inch rear-mount terminal against a 175 x 132.5 mm opening #
Inputs:
- Machined fascia opening: 175 mm wide by 132.5 mm high — the documented cut-out listed for the installed 7-inch model named above.
- Replacement: a 7-inch rear-panel terminal, screen size from the catalog.
- Conversion: 1 in = 25.4 mm exactly.
Rule in words: the opening a terminal needs is a drawing dimension. The screen diagonal is not an opening dimension, and the check is made dimension by dimension against the tolerances printed on the drawing.
Arithmetic:
- Nominal screen diagonal: 7 in x 25.4 mm/in = 177.8 mm.
- Cut-out diagonal: the square root of (175 x 175 + 132.5 x 132.5) mm = the square root of (30,625 + 17,556.25) mm = the square root of 48,181.25 mm, which is about 219.5 mm.
- Same diagonal in inches: 219.5 mm / 25.4 mm per in = about 8.64 in.
- Miss of the screen-size shortcut: 219.5 mm - 177.8 mm = 41.7 mm.
Result: the opening this class of 7-inch terminal needs runs 41.7 mm longer on the diagonal than the screen itself. Anyone who scales the opening from "7 inches" under-cuts by more than 40 mm and the terminal will not seat.
Decision: if the replacement's documented cut-out matches the machined 175 x 132.5 mm opening within the tolerance printed on its drawing, order it against this fascia. If any dimension differs by more than that tolerance, choose a model in the same cut-out family (the PT070 compatibility pattern) or re-machine the fascia before ordering — and never enlarge the opening "for clearance", because the gasket seats on the surfaces the drawing dimensions.
Sealing, panel thickness and retention #
The front rating in the datasheet belongs to the terminal installed the documented way: gasket in place, fascia inside the stated thickness band, retention fastened as instructed. Change any one of those and the assembly is untested. Three checks carry the sealing decision:
- Panel thickness: the gasket compresses correctly only between the minimum and maximum fascia thickness stated in the installation instructions; outside that band it under- or over-compresses.
- Retention: the clips or brackets must pull the terminal against the fascia at all the documented points; fewer points than drawn twist the gasket.
- Opening edge: the gasket path runs around the cut, so burrs, steps or an oversized opening break it.
Orientation belongs to the environment row as well: portrait HMI panel mounting and temperature derating go together, so read the orientation limit before the terminal goes on its side. In dusty surroundings the sealing requirement dominates the selection, which is the separate exercise covered by selecting an IP65 industrial touchscreen for a dusty HMI.
Same platform, but verify the download target #
The rear-mount variant keeps the engineering platform: the MT8070iER programs with EasyBuilder Pro, the same tool as its framed counterpart, so the existing project is the starting point, not a rewrite. What changes hands is the target. Open the project, confirm the exact model is selected as the download target, and re-check the communication driver and the controller addresses before transfer. Mounting behind a fascia does not touch a single tag: a wrong value on the new install is a binding or driver issue, never a mounting issue. After the download, verifying the HMI project version running on the panel closes the commissioning loop.
Accept the terminal in the finished fascia #
Accept the installation in its final position, not on the bench — the fascia changes edge access without changing the project. Lock out the machine and confirm the panel is de-energized before any cutting, drilling or wiring behind it. Then check:
- Every on-screen control is fully visible through the opening, edge objects included.
- Touch responds across the whole usable area, corners included; a control you can see but not press is an opening-alignment fault, not a software fault.
- Live values update from several known controller addresses, not just one.
- Connectors stay reachable with the cabinet fully wired — service access belongs to the mounting design, not to luck.
One wrong value points at that object's binding. Several values dead at once point at the driver, the cable or the controller. None of it is caused by rear mounting, and none of it is fixed by re-cutting the fascia.
Questions asked
Does a 7-inch screen size tell me the panel opening I need to cut?
No. One documented 7-inch panel-mount terminal needs a 175 x 132.5 mm opening, which is about 219.5 mm (8.64 in) on the diagonal while the screen diagonal is only 177.8 mm. The opening, its tolerances and any corner detail come from the model's dimensioned drawing, never from the screen size. Two terminals with the same screen size can need different openings.
Can I rear-mount the framed MT8070iE instead of the rear-mount variant?
No. Weintek lists the MT8070iER specifically for rear-panel mounting, and that listing is what carries the mounting features the fascia design depends on. The MT8070iE shares the 7-inch screen and the EasyBuilder Pro platform, but you would be ordering a framed housing the rear-mount design does not use, with no documented retention behind a cut fascia.
Does the terminal's front rating still apply once it is behind the fascia?
Only for the assembly installed as documented. The published front rating belongs to the terminal mounted with its own gasket, within the stated panel thickness range, with the specified retention fastened as instructed. A fascia that is too thick, too thin or warped, or an opening cut oversize, can break the seal path, so treat the rating as a property of the installed combination, not of the terminal alone.
Does the EasyBuilder Pro project need a rebuild for the rear-mount variant?
No rebuild is expected, because the rear-mount variant is documented to program with EasyBuilder Pro on the same platform as its framed counterpart. What you must do is open the project, confirm the exact target model is selected, and re-check the communication driver and controller addresses before you download. After the transfer, confirm the running project version on the panel as part of commissioning.
How much rear clearance should I leave behind the terminal?
Take the housing depth from the rear-view drawing, then add the space the largest connector plus its service loop occupies, and the space your hands need to reach those connectors in place. Depth alone is never the number to design to: a terminal can fit the depth and still be unserviceable behind a wired cabinet. Design to drawing depth plus connector and service access, verified against the cabinet layout.