HMI and touchscreens
Earlier articles
How-to
Setting Up a Weintek MT6050IP With a Delta DVP28SV PLC
Use EB8000 for the MT6050IP, because EasyBuilder Pro does not list it. Create the project, select the exact panel model, configure the Delta DVP28SV as the PLC device with serial settings copied value-for-value from the wired port, then bind objects to the device areas the Delta driver already exposes. Model, connection and address are three separate checks.
How-to
Wiring an M221 PLC to an HMI over RS-485
Bridge SDA to RDA and SDB to RDB at the HMI connector and run the junctions to M221 RJ45 pin 5 (D0) and pin 4 (D1), with ground as the third wire. Two wires on the panel's pins 1 and 2 leave one direction of the pair open; join the pairs, match the serial settings on both ends, and the link comes up.
Troubleshooting
Why the Touchscreen Number Pad Fails on One HMI Table
When the on-screen number pad opens on every table but one, the fault is that table's stored configuration, not the project. Script-generated column attributes corrupted the touchscreen settings in the case behind this article: clear the column attributes data, rebuild the columns manually, and verify a numeric cell opens the pad. Replacing the table object does not fix it.
Troubleshooting
Fixing EasyBuilder Pro simulation failure on Windows XP
When online and offline simulation stop working for every EasyBuilder Pro project on Windows XP after an upgrade, the installed build is the defect: 5.05.02.093 fails simulation on Windows XP while running on Windows 7, and 5.05.02.108 is the corrective release. Read the build number before touching the project, the PLC settings or EB8000.
Troubleshooting
Fix a Vijeo Designer Popup Blocked by a Script Busy Wait
The popup is queued, not broken: while the script's do...while loop counts to 100000, the runtime paints nothing, and the close and navigation that follow overtake the open request. Delete the loop, run the save in stages that each return control, and call close(), open(x, y) and show(true) only after changePanel(panelID) returns true.
Troubleshooting
Why a Browser HMI Tab Goes Black for 20 Seconds
A whole-tab black screen that clears after 20 to 30 seconds is client memory pressure paging the renderer to disk until proven otherwise, not a gateway, session-timeout or remote tag-provider fault. Capture RAM, committed memory, paging and disk activity on the client during the event before changing any setting; with 16 or more tabs open, the client is the layer to measure first.
How-to
How to calculate daily flow totals and midnight rollover in WinCC
Yes — no archive query is needed. One C action in the Global Script editor, on a several-second cyclic trigger, keeps today's running total; a time-based trigger at 00:00 rolls it, so yesterday takes today's value and today restarts at zero. Compute each day as a totalizer difference when the meter reads cumulative mass, or as flow × elapsed seconds ÷ 3600 when it reads a rate, and give the calculation one owner: the PLCs, or one designated server.
How-to
Configuring Dual LAN HMI Ports for Two PLC Networks
Yes. A dual-LAN HMI terminal with two independently configurable interfaces reads a PLC on each network when LAN1 and LAN2 carry non-overlapping subnets and sit on physically separate segments. A remote client on the LAN1 side reaches the terminal itself over VNC, cMTViewer, OPC UA or Modbus TCP, but not the devices behind LAN2.
Troubleshooting
Scaling a 32-bit float Modbus value in an HMI script
The divide returns zero because a w32s script operand is signed 32-bit integer arithmetic: it divides the raw bit pattern, not the float those bits encode. Define the pressure as a float variable with Bit Length 32 mapped to the two-word register pair, and run the division by 100 in the ladder logic program, where floating-point math is supported.
How-to
Searching Vijeo Designer Recipes by Label Code
Vijeo Designer addresses recipes by number only, so resolve an incoming label code through a table your scripts maintain: mirror every label in a STRING array, pack one 8-bit hash character per recipe into a 100-character STRING, seed both at power-up through a Status listener, and search with one native string scan confirmed by equals(). The method holds 100 recipes in one group; beyond that, split the hash string or search in the PLC.
Troubleshooting
Cleaning EasyBuilder Pro AppData CloudHMI Files Safely
Treat the Weintek CloudHMI xob tree under AppData\Roaming as application-managed data, not confirmed temporary cache, because no vendor documentation marks it disposable. Copy the whole tree to storage outside the VM, verify the copy, then remove the guest contents as a controlled test after closing EasyBuilder Pro. Deleting the roughly 1 GB frees guest space only; the host virtual disk shrinks after the hypervisor's documented space reclamation runs.
Explainer
How Password Security Carries From EasyBuilder 8000 to Pro
Weintek password management is not substantially changed in EasyBuilder Pro: a login sets an authorization state and each protected object checks it, exactly as in EasyBuilder 8000. Convert the MT8050iV2 password example on a copy, recompile it, and verify each protected object through three login states — the conversion cannot be reversed.