HMI and touchscreens
Earlier articles
Explainer
How Password Security Carries From EasyBuilder 8000 to Pro
Weintek password management is not substantially changed in EasyBuilder Pro: a login sets an authorization state and each protected object checks it, exactly as in EasyBuilder 8000. Convert the MT8050iV2 password example on a copy, recompile it, and verify each protected object through three login states — the conversion cannot be reversed.
Troubleshooting
EasyBuilder Pro bit lamp blink lost after upgrade
Bit lamps that still follow the bit state but never blink after the EasyBuilder Pro update show a software-version regression, not an address or driver fault. Reinstall 6.09.02.510 from Weintek or an authorized distributor, reopen the pre-update project backup, and prove the fix with a local-memory bit toggle test before any 6.10.0x editor builds the project again.
How-to
How to build an A and not B visibility condition in EasyBuilder Pro
Test A for ON and B for OFF, and write the result to one panel bit: LB10 = (LB0 = ON) AND (LB1 = OFF) is ON in exactly one of the four input states. Build it as an if condition on a cMT model, or as a macro whose GetData calls read both operands and whose SetData call writes the result bit.
Troubleshooting
Fixing EasyBuilder 8000 error 0xc0000005 at startup
EasyBuilder 8000 failing at launch with 0xc0000005 while EasyManager still opens is a Windows access violation at process start. The documented cause is Avast antivirus 5.1.889 or later hooking the editor process. Pause the shields to confirm it, then install the EasyBuilder release after EB8000V442_20110420 for the permanent fix.
How-to
Convert an MT500 Project to EasyBuilder 8000 and Resize It
EasyBuilder 8000 converts an MT500 .eob into a new .mtp project through the Tools menu; the converter selects the terminal with the nearest dimensions, so you must then select the real destination model on the Model tab and work through the resize dialog it triggers. Verify page geometry and live controller data before the panel returns to service.
Troubleshooting
Why an HMI Loses Its Program After Every Power Cycle
A flash-based panel keeps its project through power-off without a battery, so loss on every cycle means a supply dip below the panel's documented limit, a transfer that never completed, or failing storage. Classify what the screen shows at restart, capture the supply voltage at the terminals through a switch-off and on, then do one clean transfer and prove it survives a controlled power cycle.
Selection guide
Selecting a Rear-Panel Mount HMI for Machine Fascia Installation
Order the model the manufacturer explicitly lists for rear-panel (open-frame) mounting — Weintek's 7-inch MT8070iER rather than the framed MT8070iE — then verify cut-out, mounting points, panel thickness, rear clearance and gasket sealing against the dimensioned drawing before the fascia is cut. Screen size never sets the opening; the drawing does.
Explainer
What an HMI Is and How a Touch Panel Runs One
An HMI is the hardware or software through which an operator watches and commands a controller. It is not written in a general-purpose language: you configure screens in a vendor engineering editor, compile the project into a runtime, and the touch panel computer runs that runtime while exchanging variables with the control logic over a driver you verify first.
How-to
Converting a version 5.10 MER file for FactoryTalk View 7.0
Restore the version 5.10 archive in FactoryTalk View Studio 6.10 on a 32-bit Windows host; opening it there converts the tag database to the current format, so you export the tags and import them into the version 7.0 project on the 64-bit host. The Legacy Tag Database Conversion utility never runs, because Rockwell documents it as unnecessary once the upgrade to 6.1 or later happens on 32-bit Windows.
Selection guide
How to Select HMI Specifications That Match the Machine and Site
Select an HMI by walking each machine and site requirement back to the one specification that controls it: display resolution against viewing distance, the exact driver against your controller, the OS against the toolchain, the rating against the cleaning method. Hold smallest text at 3.5 mm cap height for a 600 mm stand, treat IP65 as a front-face rating that converts to no NEMA type, and keep safety functions out of the project file.
Troubleshooting
How to check PROFIBUS termination when an HMI reads no data
Isolate power, set both segment ends' termination switches ON and every middle connector OFF, then measure between A and B at any opened connector: two 220 Ω terminations in parallel give 110 Ω ± 5 Ω on a healthy bus. About double means one termination is dead, open means a broken conductor, near zero a short; if the bus reads right, the fault is in the driver, address or transmission-rate configuration.
How-to
Programming a Fatek PLC Through a Weintek HMI Ethernet Link
Yes — the FBs-20 can be programmed from a PC through the panel with only the console's one Ethernet cable. Bridge the panel's RS232 line over Ethernet with the panel's pass-through feature or an Ethernet-to-serial converter, present it to the PC as a virtual COM port, then open that port in WinProladder with the PLC's own baud, parity and station number and a raised timeout, because the panel's polling shares the line.