Troubleshooting
Why only serial appears when transferring to a TP177 Micro
Short answer
WinCC flexible 2004 Micro lists serial only for the TP177 Micro because USB/PPI multimaster cable support for that panel starts in releases later than 2005 SP1; WinCC flexible 2008 and higher document the USB/PPI Multi-Master cable transfer type. The cable itself is proven by the working S7-200 transfer. Use serial on 2004 Micro, or move to a supported release with cable 6ES7901-3DB30-0XA0 version 05 or later.
On this page
- Why does only serial appear when I select the TP177 Micro?
- Which WinCC flexible version supports USB transfer to the TP177 Micro?
- Why does the USB/PPI cable work on my S7-200 but not on the panel?
- Which USB/PPI cable does the TP177 Micro need?
- How do I transfer the project while staying on WinCC flexible 2004 Micro?
- What do I check when USB still does not appear after an upgrade?
- Questions asked
Only serial appears because WinCC flexible 2004 Micro has no USB transfer path for the TP177 Micro target: USB/PPI multimaster cable support for this panel starts in releases later than WinCC flexible 2005 SP1. Your cable is not the problem — the working S7-200 transfer proves the cable, its driver and the PPI link end to end. What fails is the second gate, the installed engineering software's TP177 Micro profile, which offers serial only. Two paths work from here: download over the serial interface the 2004 Micro install already provides, or move the engineering software to a WinCC flexible release past the multimaster threshold and use the cable hardware version the panel documentation names. Below, the three gates are separated, the version comparison is worked with real numbers, and every case ends in a decision.
Why does only serial appear when I select the TP177 Micro? #
Only serial appears because the transfer-interface list is built from the installed WinCC flexible release and the selected panel target, and the TP177 Micro profile in a 2004 Micro install contains no USB entry — the list is a software fact, not a cable fault.
WinCC flexible filters what it offers by the device you have selected. The USB entry you can find in the software's general communication settings belongs to other connection types and other devices; it is not proof that the TP177 Micro target carries a USB transfer path in the installed release. The panel has been configurable since WinCC flexible Micro 2004 SP1, so the target itself is present and configurable in your install — configuration support and USB transfer support are different features, and your install has the first without the second. Decision: the panel selection is correct and the list is honest for this release. Stop swapping cables and check the release level.
Which WinCC flexible version supports USB transfer to the TP177 Micro? #
USB/PPI multimaster cable transfer to the TP177 Micro starts in WinCC flexible releases later than 2005 SP1, and the WinCC flexible operating-system-update documentation lists the USB/PPI Multi-Master cable as a transfer type from WinCC flexible 2008 on, including 2008 V2.0.
The threshold wording matters: WinCC flexible 2005 SP1 itself sits on the serial side of the line, and the releases the transfer documentation names alongside the USB/PPI Multi-Master cable start at WinCC flexible 2008 — so treat anything at or below the 2005 SP1 level as serial-only and anything from 2008 up as USB-capable.
Worked comparison, arithmetic shown. Case 1: installed release WinCC flexible 2004 Micro SP1, threshold later than 2005 SP1. Release years compare first: 2004 < 2005, so the install sits a full release year below the threshold before any service pack enters the comparison. USB cannot appear for this target, and no cable, driver or reinstall of the same release can add it.
Case 2: installed release WinCC flexible 2008 V2.0. 2008 > 2005, so the release clears the threshold, and WinCC flexible 2008 and higher document the USB/PPI Multi-Master cable as a transfer type. The USB entry should exist for the TP177 Micro on this install; if the list still shows serial, the version information, not the cable, is the next thing to read. Decision: on 2004 Micro, work serial; from 2008 on, expect USB and troubleshoot the connection, not the list.
Why does the USB/PPI cable work on my S7-200 but not on the panel? #
The cable is not the problem: a working S7-200 transfer proves the cable, its driver and the PPI link end to end, but it proves nothing about the TP177 Micro entry in the installed WinCC flexible release, which offers that target serial only in 2004 Micro.
Three separate compatibility questions sit between your project and the panel, and the S7-200 test settles only the first:
- Cable to device: does the cable and its driver carry PPI to the connected device? Your working S7-200 transfer answers yes.
- Cable to panel: does the panel hardware accept this cable for a PC connection? The TP177 Micro documentation says yes, for the cable hardware version it names.
- Release to target: does the installed WinCC flexible release expose USB transfer for the TP177 Micro profile? In 2004 Micro, no — serial only.
Swapping or re-seating the cable re-tests only the first question, and the third changes only when the release changes. Decision: with the S7-200 transfer already proven, the release check, not another cable, is the next step.
Which USB/PPI cable does the TP177 Micro need? #
The TP177 Micro documentation names one PC cable for this work: the USB/PPI cable 6ES7901-3DB30-0XA0 from hardware version 05 upward, so a cable older than version 05 misses the panel's documented requirement even if it transfers to an S7-200 without complaint.
The hardware version is part of the cable's identity, not a software setting, so read the version marking on the cable itself. The USB side plugs into the PC and the PPI side into the panel, which is why one cable physically serves the S7-200 and the panel while the software decides what each target can do with it. On WinCC flexible 2004 Micro the cable question is moot for downloads because the list offers serial anyway; it becomes decisive the day you install a release past the threshold, so check the marking before that move. Decision: for USB transfer, use the USB/PPI cable 6ES7901-3DB30-0XA0 at hardware version 05 or higher; older hardware stays on the serial path.
How do I transfer the project while staying on WinCC flexible 2004 Micro? #
Stay on WinCC flexible 2004 Micro and use the serial transfer path the software does offer: select TP177 Micro, open the transfer settings, choose the serial interface, and download over a PPI serial cable, because serial is the supported interface for this target in that release.
Run it as the release intends:
- Select TP177 Micro as the device first, so every following dialog is built for that target.
- Put the panel into transfer mode from the panel side, the way the device manual describes for a project download.
- In the transfer settings, choose the serial interface for the selected panel and match the PC port parameters to the cable in hand.
- Start the transfer from WinCC flexible and let the configuring PC check the connection before any data moves.
- If the panel came off another machine carrying an unknown project, read it out before you overwrite anything: the walkthrough on uploading a program from an old touchscreen HMI explains the panel-side settings that decide whether an upload is possible at all.
An operating system update on this release rides the same serial path, and its loader settings are a separate exercise: the TP177 Micro PPI serial OS-update configuration guide covers the DIP switch and loader side, and the guide on getting the right firmware file for a legacy HMI panel covers choosing the file itself. Decision: serial is not a workaround on WinCC flexible 2004 Micro — it is the supported interface for this target, and one clean serial transfer closes the case without touching the software.
What do I check when USB still does not appear after an upgrade? #
Read the exact release and service pack from the engineering software's own version information before anything else, because the transfer list is decided by that exact level, and an install older than you believe will keep showing serial no matter which cable is plugged in.
Then work the rest in order:
- Reselect TP177 Micro after the software change so the interface list is rebuilt for the target instead of carried over from the previous selection.
- Confirm the installed edition still covers the Micro panel family — the panel's profile has to exist in the edition on the PC, and a release level alone does not add it.
- Check the cable's version marking against the version 05 requirement before blaming the installation.
- When USB appears but the transfer fails, the release question is closed: move to the cable, driver and port checks your proven S7-200 setup already passed once.
Decision: USB listed after a verified install — transfer over USB. Serial still alone after a verified install — that edition lacks the panel's USB profile, and the serial path remains your supported route.
Questions asked
Do I need the full WinCC package to get USB transfer to the TP177 Micro?
No. The gate is the WinCC flexible release level, not the SCADA package. A WinCC flexible release later than 2005 SP1 is what adds USB/PPI multimaster cable transfer for this panel, so keep the edition that covers the Micro panel family, install that release, and confirm the USB entry appears when TP177 Micro is selected.
The compatibility page pairs the TP177 Micro with the USB/PPI cable, so why does my list show serial only?
The compatibility listing pairs the panel with the cable at the hardware level; the transfer-interface list in the engineering software adds the release level on top. Both are true at once: the panel accepts the cable, and a WinCC flexible 2004 Micro install still offers serial only because its TP177 Micro profile predates USB transfer support.
Could a missing USB driver on the PC cause the serial-only list?
No. A missing or wrong cable driver shows up later, when the transfer tries to open the connection and fails or times out. The interface list itself comes from the installed release and the selected target, so a serial-only list with TP177 Micro selected is a release-level result, not a driver problem.
Do I have to calibrate the touch screen after an operating system update?
Yes. The device documentation for this panel family calls for calibrating a touch panel after an operating system update and before the following project transfer, so presses land where the new screens expect them. Do the calibration when the panel asks for it, then start the transfer.