IMDTouchKnowledge BaseShop main store

Troubleshooting

When the firmware upgrade utility cannot upgrade an HMI terminal

HMI and touchscreens Published 6 min read

Short answer

Before you blame the cable, read the terminal's installed firmware revision. PanelView 550 revisions 1.04 through 1.07 cannot be upgraded by the Firmware Upgrade Utility, and some very early Series A terminals, version 1.05 and earlier, lack the onboard memory for firmware versions 2, 3, and 4. If the terminal falls in either group, no cable, reset sequence, or retry changes the outcome: match the application to the installed revision or replace the terminal.

On this page
  1. Read the installed revision first
  2. Two limits block the upgrade before the cable matters
  3. Deciding a used Series A terminal that reports revision 1.05
  4. When the revision clears the limit, check the 1747-UIC path
  5. When the terminal cannot take your application
  6. Questions asked

A used HMI terminal that refuses your application and then refuses to connect to the Firmware Upgrade Utility usually is not a cabling problem. Check the installed firmware revision first. The upgrade notes for the PanelView 550 list revisions 1.04 through 1.07 as not upgradeable by the Firmware Upgrade Utility, and some very early Series A terminals, version 1.05 and earlier, do not carry enough onboard memory to hold firmware versions 2, 3, or 4. If the terminal you are working on falls in either group, no adapter swap, reset sequence, or retry changes the outcome. Read the revision, decide against the two limits below, and either match the application to the installed revision or replace the terminal.

Read the installed revision first #

The revision check costs nothing and it decides everything that follows. Power the terminal and read its identity information before the application loads: units of this generation show model, series, and firmware revision on a startup screen or in the setup and diagnostics display. Record all three values exactly. Do not infer the revision from the application's incompatibility message, and do not accept a used seller's description as the revision.

Two limits block the upgrade before the cable matters #

The first limit is the revision range. The vendor's knowledge base entry for this terminal states that revisions 1.04 through 1.07 cannot be upgraded by the Firmware Upgrade Utility. For those revisions the utility cannot perform the upgrade at all, so a reset prompt that is never satisfied is the expected outcome, not evidence of a wiring fault.

The second limit sits underneath the first. Some very early Series A terminals at version 1.05 and earlier, shipped around 1993 and 1994, do not have enough onboard memory to be upgraded to firmware versions 2, 3, or 4. No cable, adapter, or utility retry adds flash memory to the board, and an upgrade that fails for lack of flash space fails the same way on every retry, because the retry has nothing new to write into.

Sort what you are seeing against the two limits:

  • The application reports a firmware version incompatibility. Compare the revision the application was built for with the revision you read from the terminal; the message is about firmware, not about your cable.
  • The utility asks for a reset and never detects one. If the installed revision is 1.04 through 1.07, this is the documented upgrade limit, so stop retrying.
  • The terminal is Series A at version 1.05 or earlier. Treat the memory limit as a real possibility and do not plan on later firmware until you know what this specific unit can hold.
  • The revision is outside 1.04 through 1.07 and the utility still never detects the reset. Now the connection is the suspect; work through the adapter checks below.

Deciding a used Series A terminal that reports revision 1.05 #

The two thresholds in this example are the documented limits; the terminal readings are an illustrative used-market case, worked the way you would work your own.

Inputs:

  • Terminal: PanelView 550, Series A, installed firmware revision 1.05, read from the startup identity screen.
  • Application: built for firmware version 4, the revision its development package targeted.
  • Documented limit 1: the Firmware Upgrade Utility cannot upgrade revisions 1.04 through 1.07.
  • Documented limit 2: some very early Series A units at version 1.05 and earlier lack the onboard memory for firmware versions 2, 3, and 4.

The rule in words: the terminal can take the application only if it passes both checks, the installed revision lying outside the blocked utility range and the hardware carrying the memory the required version needs.

The arithmetic:

  • Revision check: 1.04 ≤ 1.05 ≤ 1.07, so the installed revision lies inside the blocked range, and the Firmware Upgrade Utility cannot upgrade this terminal to any later revision.
  • Memory check: the unit is Series A at 1.05, the exact boundary of the early group of 1.05 and earlier, so it is a candidate for the memory limit; on a memory-limited unit, versions 2, 3, and 4 cannot be installed at all.

Result: no upgrade path from revision 1.05 to version 4 exists on this hardware. The utility refuses the entire range outright, and on an early-memory unit there is no flash space for the later image even in principle.

Decision: for any installed revision from 1.04 through 1.07 the utility path is closed, and at 1.05 that verdict stands whether or not the memory limit applies to this specific board. Do not buy a second 1747-UIC and do not repeat the reset cycle. Re-save or rebuild the application for the installed revision and accept its feature set, or replace the terminal with hardware that runs version 4.

When the revision clears the limit, check the 1747-UIC path #

If the installed revision lies outside 1.04 through 1.07 and the utility still never detects the reset, the connection becomes the suspect. Prove it one change at a time instead of swapping hardware on a hunch. Put the machine in a state where it cannot move first, because reset cycles and flash attempts drop the operator interface while the rest of the system keeps running.

  • Connect the 1747-UIC to the terminal port the upgrade procedure specifies for this model.
  • Set the computer and the utility to the same communication path, and watch the adapter's status indication while the utility waits for the reset.
  • Confirm the utility targets the correct terminal and not another station on the same link.
  • Take the utility and the firmware file from the vendor's official download center, matched to the exact model.

Use the terminal and adapter manuals for the supported port, cabling, and configuration. The reset prompt alone never convicts the adapter, and a communications link that does come up still does not prove an upgrade is possible, because the revision range and the memory limit remain separate decisions.

When the terminal cannot take your application #

If the application genuinely needs version 4 features and the terminal cannot take that version, the decision is already made: keep the old unit only if an application built for its installed revision does everything the operator needs. Which development package talks to which panel is its own exercise, and Which HMI Software Works With Which HMI Panel Hardware sorts it out before you draw a screen.

If you would rather source another used unit, verify the exact revision before money changes hands; How to Verify an Obsolete HMI Replacement Before Ordering is the checklist for that. When the repair is not worth it, replacing the terminal removes both ceilings at once, because current industrial panel PCs do not carry a 1990s revision cut-off — see Planning an HMI Terminal Replacement From an Older Operator Panel for the swap, step by step.

Questions asked

Does the identification label on a PanelView 550 show the firmware revision?

The label identifies the model and series, which is enough to spot a Series A unit, but it is not proof of the installed revision: a used terminal may not still run the firmware it shipped with. Read the revision from the terminal's startup identity screen or diagnostics display, and record it with the model and series before you decide anything.

Can a terminal stuck at revision 1.04 to 1.07 still be used?

Yes. The revision limit only closes the upgrade path, not the terminal itself: it runs applications built for the revision it already has. Keep the feature set within what that revision supports, build or re-save the application accordingly, and expect no later-firmware objects to work. The unit remains a valid terminal, or a matching spare for others of the same revision, as long as the application targets what is installed.

Is a repeating reset prompt ever caused by the 1747-UIC itself?

It can be, but only on a terminal whose revision is eligible for the upgrade. When the installed revision is 1.04 through 1.07, the prompt repeats because the utility cannot perform that upgrade, and no adapter changes it. Read the revision first; on an eligible terminal, the adapter, its cabling, the computer's port setting, and the targeted node become the real suspects.

Where should the firmware file and the upgrade utility come from?

From the manufacturer's own download center or an authorized distributor, matched to the exact terminal model. Files passed around on forums or auction listings cannot be verified, and a mismatched image destroys the one thing this troubleshooting depends on: knowing exactly what is installed. Take the utility, the firmware, and the upgrade procedure from the same official source so the revision checks stay valid.

Keep reading

  • Troubleshooting

    Fixing HMIRTM.EXE Runtime Crashes on a Comfort Panel

    The HMIRTM.EXE serious error is the HMI runtime crashing on the panel itself, most often because internal storage filled with accumulated logs. Back up to a USB stick from the panel operating system, delete the logs, and stop the runtime before changing the IP address; the failed ping is a network fault that sits below the project layer.

    HMI and touchscreens

  • Troubleshooting

    Getting the Right Firmware File for a Legacy HMI Panel

    Before you chase a firmware file, decide which of three things the panel actually lacks: a communications fix, an application restore, or an operating-system image. A panel that boots and navigates almost never needs firmware, and the only safe source for the image is the manufacturer or an authorized distributor, matched to the exact nameplate model and revision.

    HMI and touchscreens

  • Selection guide

    Planning an HMI Terminal Replacement From an Older Operator Panel

    Decide an operator-terminal replacement on installed cost — the terminal, cutout adaptation, application software, engineering, commissioning, downtime and a spare — never on terminal price alone. Measure the opening against the replacement's documented cutout range and count displays before ordering: a slightly smaller terminal needs a bezel adapter, and a large converted application can force the higher-performance model. Convert in the same brand when the source project opens cleanly; rebuild cross-brand when you accept the extra engineering hours for source control.

    HMI and touchscreens